ar0330p8001q

Remove/install flywheel / drive plate

ประเภท ar · หัวข้อ 03.30 · เวอร์ชัน 0107 · 2009-01-14

ใช้กับ: ENGINE 271.940 in MODEL 203.042 /242 /742, 209.342 /442 with TRANSMISSIONS 716.6, 722.6 ENGINE 271.946 in MODEL 203.046 /246 /746 with TRANSMISSIONS 716.6, 722.6 ENGINE 271.948 in MODEL 203.040 /240 /740 with TRANSMISSION 716.6, 722.6 ENGINE 271.921 in MODEL 203.730 with TRANSMISSIONS 716.6, 722.6 ENGINE 271.955 in MODEL 209.341 /441 with TRANSMISSIONS 716.6, 722.6 ENGINE 271.942 in MODEL 203 with TRANSMISSION 716.6, 722.6 ENGINE 271.957 in MODEL 203.741 with TRANSMISSION 716.6, 722.6

ไม่มีใน “th” แสดงเป็น อังกฤษ

ตำแหน่ง

กลุ่มฟังก์ชัน 1 Engine › 03 Crank assembly › 03.30 Flywheel, driving disc, vibration damper, starter ring gear — ซีรีส์ 203 · ซีรีส์ 209 (รุ่น 341, 342, 441, 442)

EinPAS 15 Engine › 15.15 Combustion engine, complete/engine housing/crank assembly › 15.15.41 Crankshaft/flywheel/drive plate — ซีรีส์ 203 · ซีรีส์ 209 (รุ่น 341, 342, 441, 442)

ใช้กับเครื่องยนต์/เกียร์ด้วย: 271 921, 271 940, 271 942, 271 946, 271 948, 271 955, 271 957, 716 6**, 722 6**

AR03.30-P-8001Q

Remove/install flywheel / drive plate

12.12.08

ENGINE 271.940 in MODEL 203.042 /242 /742, 209.342 /442 with TRANSMISSIONS 716.6, 722.6

ENGINE 271.946 in MODEL 203.046 /246 /746 with TRANSMISSIONS 716.6, 722.6

ENGINE 271.948 in MODEL 203.040 /240 /740 with TRANSMISSION 716.6, 722.6

ENGINE 271.921 in MODEL 203.730 with TRANSMISSIONS 716.6, 722.6

ENGINE 271.955 in MODEL 209.341 /441 with TRANSMISSIONS 716.6, 722.6

ENGINE 271.942 in MODEL 203 with TRANSMISSION 716.6, 722.6

ENGINE 271.957 in MODEL 203.741 with TRANSMISSION 716.6, 722.6

Remove/install flywheel / drive plate

P03.30-2025-06

1 Bolts

2 Flywheel

3 Cylinder pin

4 Clutch plate

5 Disks

Remove/install

Danger!

Risk of death caused by vehicle slipping or toppling off the lifting platform.

Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer.

AS00.00-Z-0010-01A

1

Remove transmission

Transmission 716.6

Manual transmission

AR26.10-P-0020P

Transmission 716.6 with
automated manual transmission code 424

AR26.10-P-0020E

Transmission 722.6

Automatic transmission

AR27.10-P-0500P

2

Detach clutch

Transmission 716.6

AR25.10-P-0050P

3

Install retaining lock for crankshaft/starter ring gear

AR03.30-P-5000PR

4

Remove bolt (1)

Installation: If no angle tightener is available, the bolts can be turned by the specified angle in a single stroke, using a socket wrench and locking handle (1).

In order to avoid any angle errors it is not permitted to use a flexi-rod torque wrench for tightening to angle degrees as this falsifies the tightening torque.

*BA03.30-P-1003-01I

5.1

Take off flywheel (2)

Transmission 716.6

The flywheel (2) is individually balanced in the factory and can therefore be replaced without balancing.

A certain installation position of the flywheel (2) is fixed by the straight pin (3).

5.2

Take off drive plate (4) and washers (5)

Transmission 722.6

The drive plate (4) is individually balanced at the factory, and can therefore be replaced without balancing.

A certain installation position of the drive plate (4) is fixed by the straight pin (3).

6

Install in the reverse order

Flywheel, driven plate, vibration damper, starter ring gear

Number

Designation

Engine
271

BA03.30-P-1003-01I

Bolt, flywheel or two-mass flywheel / drive plate to crankshaft

Stage 1

Nm

45

Stage 2

°

90

เอกสารที่อ้างถึง