P32.25-A007-09
Shown on model 167.119 |
1 | Front shock absorber | 5 | Rear boot | |
2 | Front steel spring | 6 | Rear elastomer bearing | |
3 | Front boot | 7 | Rear steel spring | |
4 | Rear shock absorbers | 12 | Rear piston rod |
Shown on model 167.119 |
8 | Front spring retainer |
9 | Front elastomer bearing |
10 | Front piston rod |
P32.25-A008-06
Shown on model 167.119 |
11 | Rear spring retainer |
P32.25-A009-06
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Warning | Risk of injury. Moving parts can pinch, crush or, in extreme cases even sever extremities. | No parts of the body or limbs should be within the operating area of mechanical components when moving components. | |
Preparatory activity | |||
1 | Lift vehicle with lifting platform. | ||
| |||
| Check | ||
2 | Check front shock absorbers (1) for fluid loss. | ||
If necessary, use commercially available devices/tools. | |||
A light oil film on the front piston rods (10) is permissible. | |||
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
3 | Check front piston rods (10) for surface damage, corrosion and deformation. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
4 | Check that the front steel springs (2) are correctly seated in the front spring retainers (8). | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
5 | Check front steel springs (2) for fractures. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
6 | Check that the front boots (3) are seated correctly and check for damage. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
7 | Check front elastomer bearings (9) of front shock absorbers (1) for cracks, deformation and wear, as well as for play by firmly pulling and pushing at front shock absorbers (1). | ||
If necessary, use commercially available devices/tools. | |||
The front elastomer bearings (9) must be seated with zero clearance in the housing eye and they may not be cracked or damaged. | |||
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
8 | Check rear shock absorbers (4) for fluid loss. | ||
If necessary, use commercially available devices/tools. | |||
A light oil film on the rear piston rods (12) is permissible. | |||
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
9 | Check rear piston rods (12) for surface damage, corrosion and deformation. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
10 | Check that the rear steel springs (7) are correctly seated in the rear spring retainers (11). | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
11 | Check rear steel springs (7) for fractures. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
12 | Check that the rear boots (5) are correctly seated and check for damage. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
13 | Check rear elastomer bearings (6) of rear shock absorbers (4) for cracks, deformation and wear, as well as for play by firmly pulling and pushing at rear shock absorbers (4). | ||
If necessary, use commercially available devices/tools. | |||
The rear elastomer bearings (6) must be seated with zero clearance in the housing eye and they may not be cracked or damaged. | |||
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
Finishing activity | |||
14 | Lower vehicle with vehicle lift. | ||
|