AN82.88-W-0001MPA | Retrofit toll system | 14.2.12 |
MODEL 930, 932, 933, 934
with CODE (F04) Cab L (long)
except CODE (DD1) Cab with 1400 mm floor-to-ceiling height (car transporter)
except CODE (DD2) Cab with 1550 mm floor-to-ceiling height
except CODE (DD3) Lowered cab with low roof
except CODE (EX3) Telematics preinstallation
Grundig toll system
MODEL 930, 932, 933, 934
with CODE (F15) MEGASPACE cab
except CODE (EX3) Telematics preinstallation
Grundig toll system
W82.88-1055-06
Shown on model 934 with
Code (F04) Cab L (long)
1 Multifunction antenna
2 On-board unit
(toll acquisition device)
3 DSRC communication module
W82.88-1065-05
Connection scheme
2 On-board unit
(toll acquisition device)
3 DSRC communication module
A7 Base module (GM)
F13 Fuse toll system, term. 30
F27 Fuse toll system, term. 15
GPS GPS antenna
GSM GSM antenna
P3 Modular tachograph (MTCO)
Modification notes
| Install | ||
1 | Install support battery in the On-Board-Unit (toll acquisition device) (2) | ||
2 | Store vehicle and customer data with the service PC in the On-Board-Unit (toll acquisition device) (2) | The procedure on the service PC can be obtained from the documents from the course "Installation of vehicle device" of the Toll Collect company. | |
3 | Open sliding roof | ||
4 | Switch off ignition | ||
Danger! | Risk of explosion caused by escaping oxyhydrogen gas. Risk of injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte (contains diluted sulfuric acid) or metal spatter due to short circuit. Risk of burn injuries caused by short circuit. Risk of poisoning caused by swallowing battery electrolyte (contains diluted sulfuric acid) or absorption of lead over the skin or orifices | No fire, sparks, open flames or smoking. Wear acid-resistant gloves and clothing and safety glasses with side guards. Do not place any conductive objects on the battery and avoid any short circuit from battery positive to ground. Only fill liquid battery electrolyte (diluted sulfuric acid) into suitable and appropriately marked containers. | |
5 | Disconnect ground lead from battery | ||
| Notes on battery | ||
6 | Remove modular tachograph (MTCO) (P3) | ||
| |||
7 | Remove driver-side interior lamp | ||
8 | Remove center stowage box above windshield | ||
| |||
9 | Remove closing strip of lower roof stowage compartment | The length of the end strip depends on the installed equipment. | |
| |||
10 | Remove speaker cover above | ||
11 | Remove paneling on the passenger-side A-pillar | The support rod must be reattached for the duration of the installation process after removing the paneling. | |
| |||
12 | Remove footwell cover on the front passenger side | ||
| |||
13 | Install bracket for the on-board unit (toll collection unit) (2) | ||
14 | Install multifunction antenna (1) | ||
| | ||
15 | Install the extension lines for the multifunction antenna (1) | ||
16 | Install wiring harness for toll system | ||
17 | Connect wiring harness for toll system to modular tachograph (MTCO) (P3) | ||
18 | Connect wiring harness for toll system in electrical compartment | ||
19 | Connect and install DSRC communication module (3) | ||
| |||
20 | Adjust turn rate sensor (gyro) of On Board Unit (toll acquisition device) (2) | ||
| |||
21 | Connect and install On Board Unit (toll acquisition device) (2) | ||
22 | Install remaining parts onto vehicle | ||
23 | Synchronize modular tachograph (MTCO) (P3) | ||
24 | Check operation and carry out road test |
Grab handle
Number | Designation | Body | |
BA68.70-N-1001-01A | Screw for grab handle on cab | Nm | 18 |
Antenna toll system
Number | Designation | Models | ||
BA82.88-N-1001-01A | Hirschmann multifunction antenna GPS 925/DCS on roof | Nm | 7 (1) | |
Choke angle gauge (electronic)
001 589 88 21 00
Parts ordering notes
Part no. | Designation | Quantity |
-- | Installation kit for Grundig toll system | 1 |
B6 782 1148 | Assembly set FB (dual DIN slot) | 1 |
B6 782 1170 | EX3 assembly parts | 1 |
B6 782 1096 | DIN slot covering | 1 |