ar0920d131007d

Detach/attach intake manifold at cylinder head

Тип ar · тема 09.20 · версия 0102 · 2004-04-14

Применимость: ENGINE 111.979 in MODEL 902.061 /062, 903.061 /062 /063, 904.062 /063 with CODE (KL8) Pressurized gas reservoir in cargo area with CODE (MS7) NGT (Natural Gas Transporter) sprinter ENGINE 111.979 in MODEL 902.012 /062 /072, 903.012 /013 /022 /062 /063 /072 /073, 904.012 /013 /062 with CODE (KL9) Pressurized gas reservoir underfloor arrangement with CODE (MS7) NGT (Natural Gas Transporter) sprinter

Нет на языке «ru»; показано на языке Английский.

Расположение

Функциональная группа 1 Двигатель › 09 Система впуска, наддув воздуха › 09.20 Впускной коллектор, подогрев впускного коллектора — Серия 902 (модели 012, 061, 062, 072) · Серия 903 (модели 012, 013, 022, 061, 062, 063, 072, 073) · Серия 904 (модели 012, 013, 062, 063)

EinPAS 15 Двигатель › 15.30 Система впуска / наддув › 15.30.33 Впускной коллектор / патрубок наддувочного воздуха — Серия 902 (модели 012, 061, 062, 072) · Серия 903 (модели 012, 013, 022, 061, 062, 063, 072, 073) · Серия 904 (модели 012, 013, 062, 063)

Также относится к двигателям/коробкам передач: 111 979

AR09.20-D-1310-07D

Detach/attach intake manifold at cylinder head

Intake manifold, intake manifold preheater

Number

Designation

Engine 111.979/
984

BA09.20-N-1001-02A

Intake manifold to cylinder head

M8

Nm

21

Detach/attach intake manifold at cylinder head

D09.20-1013-01

1 Detach gas hose (2) from the gas filter at the gas rail.

Remove gas hose (2) from the gas rail only after removing the intake manifold.

Installation: Use new sealing rings.

2 Remove bracket (1) with gas filter from the intake manifold.

Detach/attach intake manifold at cylinder head

D09.20-1005-01

3 Detach connector (5) from the idle speed control actuator.

4 Remove screws (4) and set the bracket (3) aside with the electrical connection.

Detach/attach intake manifold at cylinder head

D09.20-1015-01

5 Detach spring (6).

Detach/attach intake manifold at cylinder head

D09.20-1006-01

6 Remove screws (9) and nuts (8).

Installation: Tighten screws (9) and nuts (8) evenly.

Observe the tightening torque.

Detach/attach intake manifold at cylinder head

D09.20-1014-01

7 Unclip the Omega clip (10).

8 Carefully separate the intake manifold a little way from the cylinder head.

9 Detach plugs (12) from the injection valves.

10 Detach plugs (11, 15) from gas temperature and pressure sensors.

Detach/attach intake manifold at cylinder head

D09.20-1008-01

11 Lift off intake manifold (14).

12 Take off seal (13).

Installation: Clean the sealing surfaces, install new gasket (13).

13 Install in the reverse order.