S72.16-4638-09
1 | Lock striker | 4 | Middle carriage | 7 | End stop | ||
2 | Lock hook | 5 | Bottom carriage | ||||
3 | Guide wedge | 6 | Upper carriage |
Danger ! | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
| Check | ||
1 | Check gap dimensions "DC, FA, FB" | ||
| |||
Model 447 except code W65 (Liftgate) except code W68 (Electrically actuated lifgate), model 447, 448 with code W65 (Liftgate), model 447, 448 with code W68 (Electrically actuated lifgate)Gap dimensions | |||
Model 447 except code W65 (Liftgate) except code W68 (Electrically actuated lifgate), model 447, 448 with code W65 (Liftgate), model 447, 448 with code W68 (Electrically actuated lifgate)Gap dimensions | |||
Feeler gauge | |||
Adjust | |||
2.1 | Remove fuse 74 on left electric sliding door | Model 447.7/8, 448.8 | |
| Assignment of right footwell firewall fuse and relay module | ||
2.2 | Remove fuse 311 on right electric sliding door | Model 447.7/8, 448.8 | |
| Assignment of fuse and relay module, right A-pillar | ||
3 | Loosen bolts on lock striker (1) | ||
4 | Loosen lock hook (2) | ||
5 | Loosen bolts on guide wedges (3) and screw back end stops (7) | ||
6 | Remove cover below sliding carriage (5) | ||
7 | Loosen bolts on center sliding carriage (4) | ||
8 | Loosen bolts on bottom sliding carriage (5) | ||
9 | Adjust gap dimensions "DC" and "FB" | ||
Helper required. | |||
Model 447 except code W65 (Liftgate) except code W68 (Electrically actuated lifgate), model 447, 448 with code W65 (Liftgate), model 447, 448 with code W68 (Electrically actuated lifgate)Gap dimensions | |||
Model 447 except code W65 (Liftgate) except code W68 (Electrically actuated lifgate), model 447, 448 with code W65 (Liftgate), model 447, 448 with code W68 (Electrically actuated lifgate)Gap dimensions | |||
Feeler gauge | |||
10 | Tighten bolts on center sliding carriage (4) finger-tight | ||
11 | Tighten bolts on bottom sliding carriage (5) finger-tight | ||
12 | Adjust evenness of sliding door in relation to side wall with lock striker (1) and adjust end stops (7) | The front door contour must align with the side wall contour or project by a maximum of 1 mm. | |
13 | Loosen bolts on top sliding carriage (6) | ||
14 | Adjust gap dimension "FA" and evenness of sliding door in relation to front door | ||
Helper required. | |||
The front door contour must align with the sliding door contour or project by a maximum of 1 mm. | |||
Model 447 except code W65 (Liftgate) except code W68 (Electrically actuated lifgate), model 447, 448 with code W65 (Liftgate), model 447, 448 with code W68 (Electrically actuated lifgate)Gap dimensions | |||
Feeler gauge | |||
15 | Tighten bolts on top sliding carriage (6) finger-tight | ||
16 | Adjust lock hook (2) and guide wedges (3) | ||
17 | Check dimensions "DC, FA, FB" as well as check whether sliding door opens or closes correctly | ||
Gap dimension "DC"Gap dimensions | |||
Gap dimensions "FA, FB"Gap dimensions | |||
Feeler gauge | |||
If this is not the case | |||
| |||
Repeat adjustment of sliding door | |||
18 | Tighten bolts on center sliding carriage (4) | Screw/bolt, center carriage to sliding door | |
19 | Tighten bolts on bottom sliding carriage (5) | Screw/bolt, lower carriage to mount | |
20 | Tighten bolts on top sliding carriage (6) | ||
21 | Install cover above bottom sliding carriage (5) | ||
22 | Securely tighten bolts of locking eye (1) | Screw/bolt, lock striker to C-pillar | |
23 | Tighten lock hook (2) | ||
24 | Tighten bolt son guide wedges (3) | ||
25.1 | Install electrical fuse 74 on left electric sliding door | Model 447.7/8, 448.8 | |
| Assignment of right footwell firewall fuse and relay module | ||
25.2 | Install electrical fuse 311 of right electric sliding door | Model 447.7/8, 448.8 | |
| Assignment of fuse and relay module, right A-pillar |
Gap dimensions |
Number | Designation | Model 447, 448 except code W65, W68 | Model 447, 448 with code W65, model 447, 448 with code W68 | |||
BE60.00-N-1004-01J | Gap dimensions | Front door to longitudinal member | Dimension "DA" | mm | 6 (+2/-1) | 6 (+2/-1) |
Front door to sidewall | Dimension "DB" | mm | 4 (1) | 4 (1) | ||
Front door to sliding door | Dimension "DC" | mm | 4 (+1,2/-0,8) | 4 (+1,2/-0,8) | ||
Front door to A-pillar | Dimension "DD" | mm | 4,5 (+1,5/-1) | 4,5 (+1,5/-1) | ||
Front door to fuel filler door | Dimension "DE" | mm | 4 (1) | 4 (1) | ||
For picture, see | ||||||
Gap dimensions |
Number | Designation | Model 447, 448 except code W65, W68 | Model 447, 448 with code W65, model 447, 448 with code W68 | |||
BE60.00-N-1006-01J | Gap dimensions | Sliding door to roof frame | Dimension "FA" | mm | 4,5 (1,4) | 4,5 (1,4) |
Sliding door to sidewall | Dimension "FB" | mm | 4 (+1,2/-0,8) | 4 (+1,2/-0,8) | ||
Glass pane in sliding door, all-round | Dimension "FC" | mm | 3 | 3 | ||
For picture, see | ||||||
129 589 03 21 00
Feeler gauge
Documente menționate
- ar6000s070001e
- as0000z001101a Pericol de rănire prin prinderea sau strivirea degetelor la operaţii de demontare, montare şi reglare la capote, uşi, capace şi tavan culisant
- gf5415s125638tra
- gf5415s125639tra