S60.30-0080-09
Shown on left side of vehicle |
1 | Side dropside |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Topical note | Special instructions for lifting and supporting vehicle | ||
Topical note | General information on body repair | ||
Topical note | Notes on paintwork repairs | ||
General information on MB materials | |||
| Remove | ||
1 | Remove all detachable parts in area to be repaired | ||
2 | Remove platform |
| |
Model 470, 471 with engine 699 | |||
3 | Cover all detachable parts remaining in the platform with welding protection blankets | Commercially available devices/tools | |
4 | Set up straightening bench and straightening tool set | ||
| 000 588 01 23 00 Body straightening system | ||
5 | Place platform on straightening bench and fasten | ||
| 000 588 01 80 00 Swivel arm column-type lift | ||
6 | Remove side dropside (1) | ||
Commercially available devices/tools | |||
7 | Prepare side dropside (1) for installation | ||
Commercially available devices/tools | |||
| Install | ||
Danger | The high voltage used for electric welding presents a lethal hazard. Risk of explosion from welding in areas close to highly inflammable materials. Risk of injury from weld splatter and UV-light when welding. Risk of poisoning from inhaling welding gases | Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly inflammable materials from the hazard area. Use air extraction system. | |
8 | Install side dropside (1) and weld in | ||
Topical note | Measures for preventing damage to components when performing electric welding and soldering work | ||
| 000 588 02 84 00 Welder | ||
Commercially available devices/tools | |||
Bolt, dropside at front to dropside at side | |||
Bolt, bracket to dropside at side | |||
Bolt, cross member in center to dropside at side | |||
Nut, cross member at front to dropside at side | |||
Bolt, cross member at outer rear to dropside at side | |||
Bolt, cross member at inner rear to dropside at side | |||
Bolt, dropside at side to cross member at rear | |||
1K-zinc dust paint | |||
9 | Release platform from straightening bench, lift, and remove straightening bench | ||
10 | Clean weld joints and sheet metal flanges with rotary wire brush | Commercially available devices/tools | |
11 | Remove welding protection blankets | Commercially available devices/tools | |
12 | Clean repair areas | Commercially available devices/tools | |
Danger | Risk of explosion caused by paint vapors igniting. Risk of poisoning caused by inhaling paint vapors. | No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated. | |
13 | Prime repair area with primer filler | Use only primer filler approved by Daimler AG: http://xentryportal.mercedes-benz.com | |
14 | Seal seam following repairs | ||
Supplement standard seals with sealant. | |||
Danger | Risk of explosion caused by paint vapors igniting. Risk of poisoning caused by inhaling paint vapors. | No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated. | |
15 | Paint repair area adjacent surfaces | Only use paints approved by Daimler AG: http://xentryportal.mercedes-benz.com | |
Danger | Risk of explosion and poisoning caused by solvent vapors and gasses. Risk of injury to skin and eyes when working with anticorrosion agents | Never spray corrosion protection on flames or hot, glowing objects and keep them well away from all potential sources of ignition. Use them only in well-ventilated rooms; wear respiratory protection. | |
16 | Add cavity preserving agent | ||
17 | Install platform |
| |
Model 470, 471 with engine 699 | |||
18 | Install all detachable body components in area to be repaired |
Documente menționate
- ah0060n010001p Indicaţii pentru ridicare şi aşezarea pe cric
- ah6000n000101a Indicaţii generale privind reparaţiile de caroserie
- ah6000p000102a Măsuri pentru evitarea avariilor la componente la operaţii electrice de sudare, de lipire
- ah9800p940802a Indicaţii pentru vopsirea după reparaţie
- ah9800p940903a Generalităţi privind materialele MB
- ar6030s0001p
- ar6030s0001pa
- ar6030s004001p
- ar6030s004002p
- ar6030s004003p
- ar9710s4000p
- ar9720s1500p
- as0000z000701a Pericol de moarte datorită tensiunii înalte la sudura electrică. Pericol de explozie prin sudare în zona materialelor uşor inflamabile. Pericol de rănire prin stropi de sudură şi raze UV în timpul sudării. Pericol de intoxicare p
- as0000z001001a Pericol de moarte prin alunecare sau basculare a autovehiculului de pe elevator
- as0000z001701a Pericol de rănire prin tăieturi respectiv zgârieturi provocate de componentele cu muchii ascuţite ale autovehiculului
- as9700z000101a Pericol de explozie şi pericol de otrăvire prin vapori de diluanţi şi gaze. Pericol de rănire a ochilor şi pielii la prelucrarea agenţilor anticoroziune
- as9800z000201a Pericol de explozie prin aprinderea vaporilor de vopsea. Pericol de otrăvire prin inhalarea vaporilor de vopsea
- ws0000p0041b
- ws6000p0022k
- ws6000p0023k