EinPAS 35 Caroserie/Şasiu/Piese detaşabile › 35.51 Ușă pasager 1 › 35.51.32 Batante de ușă/cadru ușă — Seria 251
EinPAS 35 Caroserie/Şasiu/Piese detaşabile › 35.52 Ușă pasager 2 › 35.52.32 Batante de ușă/cadru ușă — Seria 251
EinPAS 35 Caroserie/Şasiu/Piese detaşabile › 35.53 Ușă pasager 3 › 35.53.32 Batante de ușă/cadru ușă — Seria 251
EinPAS 35 Caroserie/Şasiu/Piese detaşabile › 35.54 Ușă pasager 4 › 35.54.32 Batante de ușă/cadru ușă — Seria 251
AR60.00-P-0700-01RT
Gap dimensions on hoods, doors and lids
Test and adjustment values for gap dimensions
Number
Designation
Model 251
BE60.00-P-1001-01S
Gap dimension
Lamp unit to engine hood
Dimension "A"
mm
4 (1)
Lamp unit to fender
Dimension "B"
mm
4 (1)
Lamp unit to bumper
Dimension "C"
mm
4 (1)
Engine hood to bumper
Dimension "D"
mm
6 (1)
Engine hood to front grille/bumper to front grille
Dimension "E"
mm
7 (1)
See figure in
-
BE60.00-P-1002-01S
Gap dimension
Fender/engine hood
Dimension "F"
mm
3.5 (1)
Engine hood to A-pillar
Dimension "G"
mm
3.5 (1)
Fender to A-pillar
Dimension "H"
mm
3.5 (1)
Front fender to front door
Dimension "I"
mm
4 (1)
Front door to A-pillar
Dimension "J"
mm
4 (1)
See figure in
-
BE60.00-P-1003-01S
Gap dimension
Front door to rear door in area of B-pillar
Dimension "K"
mm
4.5 (1)
Rear door to roof frame
Dimension "L"
mm
4 (1)
Rear door to C-pillar
Dimension "M"
mm
4.5 (1)
Rear-end door to side wall
Dimension "N"
mm
5.5 (1)
Rear-end door glass to side wall
Dimension "O"
mm
5.5 (1)
See figure in
-
BE60.00-P-1004-01S
Gap dimension
Rear-end door to side wall
Dimension "P"
mm
5.5 (1)
Rear door to rear fender
Dimension "Q"
mm
4 (1)
Rear door to door sill molding
Dimension "R"
mm
6 (0.5)
Front door to rear door
Dimension "S"
mm
4 (1)
Front door to door sill molding
Dimension "T"
mm
5 (0.5)
See figure in
-
BE60.00-P-1005-01S
Gap dimension
Taillamp to bumper
Dimension "U"
mm
3,5 (1.5)
Taillamp to side wall
Dimension "V"
mm
3.5 (1)
Dimension "W"
mm
4 (1)
Taillamp to rear-end door
Dimension "X"
mm
4.5 (1.5)
Rear-end door to antenna module
Dimension "Y"
mm
5.5 (0.5)
Rear-end door to bumper
Dimension "Z"
mm
6 (1.5)
See figure in
-
Feeler gauge
129 589 03 21 00
P60.00-2687-09
Adjust hoods, doors and lids as shown in drawing. The gap should not run wedge-shaped or be too narrow at points. Deviations from parallel gap should be max. 0.5 mm over the entire length. If the inside clearance is too large or too small, the movable body parts must be centered accordingly. The reference measurements apply only for repair work on bodies damaged in accidents.
