Remove/install injection nozzle for exhaust aftertreatment system · ar1440p2000cda · Mercedes-Benz WIS

AR14.40-P-2000CDA

Remove/install injection nozzle for exhaust aftertreatment system

28.06.2019

Engine	651 in model 172
	with code U77 (Diesel Emission control BLUETEC (SCR))

Modification notes

13.10.2016

Replace seal, added.

Operation step 7

Remove/install injection nozzle for exhaust aftertreatment system

P14.40-2534-09

1	AdBlue® line	4	Coolant hoses
2	Electrical connector	Y129	AdBlue® metering valve
3	Clip

 Caution	Risk of injury caused by scraping or cutting body parts on sharp vehicle parts	Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels.	AS00.00-Z-0017-01A
 Warning	Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant.	Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. Wear protective gloves, protective clothing and safety glasses.	AS20.00-Z-0001-01A
 Warning	Risk of injury. Skin or eye injuries may result when handling hot or glowing objects.	Wear protective gloves, protective clothing and safety glasses, if necessary.	AS00.00-Z-0002-01A
 Warning	Risk of burn injuries and scalding when working at AdBlue lines and the components attached to them. Risk of injury to skin and eyes when handling AdBlue. Risk of poisoning caused by swallowing AdBlue	Pour AdBlue into suitable containers only. Wait until the pressure is released before starting any work on the exhaust aftertreatment system.	AS14.40-Z-0001-01A
Topical note	Notes on avoiding damage through contamination and foreign objects		AH00.00-P-5000-01A
Topical note	Notes on coolant		AH20.00-N-2080-01A
	Notes on use, material properties and handling of AdBlue®		AH14.40-N-0001-01A
 	Remove/install
1	Remove bottom section of soundproofing in the center and rear		AR94.30-P-5300W
2	Release and disconnect electrical connector (2)
3	Push the heat protection insulation of the AdBlue® line (1) somewhat to the rear
4	Detach AdBlue® line (1) on the AdBlue® metering valve (Y129) and close off openings with a suitable stop plug	 Installation: Replace seal.
		 Record plug	*129589009100
5	Pinch off coolant hoses (4)	 Clamp	*000589543700
6	Detach coolant hoses (4) at AdBlue® metering valve (Y129) and catch escaping coolant in a suitable container	 Installation: Replace clamps.
		 Pliers for click clamps	*171589003700
7	Open clamp (3) and then remove AdBlue® metering valve (Y129)	 Ensure correct positioning of the AdBlue® metering valve (Y129). The lugs of the AdBlue® metering valve (Y129) must sit in the grooves of the exhaust pipe. Non-observation leads to wrong assembly and damage to the AdBlue® metering valve (Y129).
		 Installation: Replace clamp (3).
		 Installation: Replace seal.
		 Bolt, AdBlue® metering valve clamp to exhaust system	*BA14.40-P-1009-02D
	Clean
8	Clean AdBlue® line (1) at connection
9	Clean seat of the AdBlue® metering valve (Y129) in exhaust pipe and close off exhaust pipe with protective cover	When replacing the AdBlue® metering valve (Y129) and for reuse of the SCR catalytic converter.
		 Set of protective covers	*001589019100
10	Install in the reverse order
11	Read out and erase fault memory
			AD00.00-P-2000-04A
	Check
12	Check coolant level and correct if necessary
	Notes on coolant level		AH20.00-P-1142-01CW
		 Coolant mixing ratio	*BF20.00-P-1001-04A
 Warning	Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.	Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.	AS00.00-Z-0005-01A
13	Perform an engine test run and check exhaust system in the area of the AdBlue® metering valve (Y129) for leaktightness

 Exhaust aftertreatment, BlueTec

Number	Designation		Engine 651 in model 172 with code U77 (Diesel Emission control BLUETEC (SCR))
BA14.40-P-1009-02D	Bolt, AdBlue® metering valve clamp to exhaust system	Nm	11

 Coolant mixing ratio

Number	Designation				Engine all (4xWD, CAR, smart)
BF20.00-P-1001-04A	Coolant mixing ratio	Antifreeze/water	Up to -37°C	%	50/50
			As of -38 °C	%	55/45
			Overview and specifications sheet		BB00.40-P-0310-01A
			References to sheet specification		BB00.40-P-0310ZZ

000 589 54 37 00

Clamp

001 589 01 91 00

Set of protective covers

129 589 00 91 00

Record plug

171 589 00 37 00

Pliers for click clamps

Documente menționate

ad0000p200004a Conectaţi STAR DIAGNOSIS, citiţi memoria de erori
ad0000p200004a
ah0000p500001a Indicaţii pentru evitarea defecţiunilor din cauza impurităţilor şi corpurilor străine
ah1440n000101a Indicaţii de utilizare, proprietăţi ale substanţei şi manipularea AdBlue
ah2000n208001a Indicaţii pentru lichid de răcire
ah2000p114201cw Indicaţii pentru nivelul lichidului de răcire
ar9430p5300w
as0000z000201a Pericol de rănire la piele şi ochi prin manipulare cu obiecte fierbinţi sau incandescente
as0000z000501a Pericol de accident prin pornirea de pe loc cu motorul aflat în funcţionare. Pericol de rănire prin striviri şi arsuri la manipularea în timpul pornirii motorului sau cu motorul aflat în funcţionare
as0000z001701a Pericol de rănire prin tăieturi respectiv zgârieturi provocate de componentele cu muchii ascuţite ale autovehiculului
as1440z000101a Pericol de arsuri şi opărire la lucrări la conductele de AdBlue şi la componente legate de acestea. Pericol de rănire a pielii şi ochilor la manipularea cu AdBlue. Pericol de intoxicare prin înghiţirea de AdBlue
as2000z000101a Pericol de rănire la piele şi ochi prin opărire cu lichid de răcire fierbinte pulverizat afară. Pericol de otrăvire datorită înghiţirii lichid de răcire.