ar0703t6831bb

Removing/installing a nozzle holder combination

Tip ar · temă 07.03 · versiune 0102 · 2005-07-12

Valabil pentru: ENGINE 457.944 in MODELS 613.358 /388 ENGINE 457.942 in MODELS 671.015 /020 /021 /030 /042 /332 /333

Nu este disponibil în „ro”; afișat în Engleză.

Încadrare

Grupă funcțională 1 Motor › 07 Pregătirea amestecului › 07.03 Injectoare, supape de injecţie, cabluri — Seria 613 (modele 358, 388) · Seria 671 (modele 015, 020, 021, 030, 042, 332, 333)

EinPAS 15 Motor › 15.45 Management motor › 15.45.42 Distribuitor combustibil/rampă/duză/injector — Seria 613 (modele 358, 388) · Seria 671 (modele 015, 020, 021, 030, 042, 332, 333)

Valabil și pentru motoare/cutii de viteze: 457 942, 457 944

AR07.03-T-6831BB

Removing/installing a nozzle holder combination

27.6.01

ENGINE 457.944 in MODELS 613.358 /388

ENGINE 457.942 in MODELS 671.015 /020 /021 /030 /042 /332 /333

Removing/installing a nozzle holder combination

A07.03-0003-01

1 Pressure screw

2 Pressure pipe connection

3 O-ring

Removing/installing a nozzle holder combination
Removing/installing a nozzle holder combination

A07.03-0002-02

4 Bolt

5 Clamping piece

6 O-ring

7 Nozzle holder combination

8 Cap

A07.03-0001-02

Removing/installing

1

Open left rear maintenance flap

Model 671. only

2

Open engine compartment flap

Model 613. only

3

Remove interior compartment flap above engine, install

Model 613. only

AR88.40-T-1100-03BA

4

Remove charge air manifold

Model 671. only

AR09.41-T-8681BB

Danger!

Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel as well as risk of injury to eyes and skin caused by contact with fuel.

No fire, sparks, open flames or smoking.
Only pour fuels into suitable and appropriately marked containers.

Wear protective clothing when handling fuel.

AS47.00-Z-0001-01A

5

Remove MR/PLD injection lines

AR07.15-T-9235BB

6

Unscrew thrust bolt (1) and pull out pressure pipe connection (2)

Installation: Replace and grease the O-ring (3).

*BA07.15-N-1004-01C

7

Remove cylinder head cover

Model 671

AR01.20-T-5014AA

Model 613

AR01.20-T-5014BA

*BA01.20-N-1001-01I

*BA01.20-N-1002-01I

8

Unbolt clamp (5)

*BA01.30-N-1006-01J

9

Pull out nozzle holder combination (7)

If nozzle holder combination is tight, use impact extractor together with threaded insert.

*904589006300

*355589016300

Installation: Replace and grease the O-ring (6). Note installation position: The locking pin (arrow) must be located opposite the cap (8).

10

Install in reverse order

Crankcase ventilation, cylinder head cover

Number

Designation

Engine 457.9

BA01.20-N-1001-01I

Bolt for light alloy cylinder head cover on cylinder head

Nm

25

BA01.20-N-1002-01I

Bolt for plastic cylinder head cover on cylinder head

Nm

20

Cylinder head

Number

Designation

Engine 457.9

BA01.30-N-1006-01J

Bolt for clamp on cylinder head

Nm

50

Diesel injection system with unit pumps (MR/PLD)

Number

Designation

Engine 457.9

BA07.15-N-1004-01C

Thrust bolt for pressure pipe connection on cylinder head

Nm

40

Removing/installing a nozzle holder combination
Removing/installing a nozzle holder combination

904 589 00 63 00

Threaded insert

Impact extractor

355 589 01 63 00

Documente menționate