ar0140b9202a
Measure cylinder bores
Tip ar · temă 01.40 · versiune 0103 · 2019-10-24
Valabil pentru: Engine 904.9, 906.9, 924.9, 926.9 in model 382, 384, 634, 685 Engine 904.9, 906.9, 924.9, 926.9 in model 693, 695 Engine 904.9, 906.9, 924.9, 926.9 Engine 906.9, 926.9 in model 958
Nu este disponibil în „ro”; afișat în Engleză.
Încadrare
Grupă funcțională 1 Motor › 01 Motor complet, sistem de ventilaţie motor, chiulasă, carter motor › 01.40 Carter motor, capac carcasă distribuţie, capac de închidere — Seria 382 · Seria 384 · Seria 634 · Seria 685 · Seria 693 · Seria 695 · Seria 904 (modele 9**) · Seria 906 (modele 9**) · Seria 958
EinPAS 15 Motor › 15.15 Motor cu ardere internă complet/Carcasă motor/Mecanism bielă-manivelă › 15.15.31 Bloc motor/Separator ulei/Aerisire — Seria 382 · Seria 384 · Seria 634 · Seria 685 · Seria 693 · Seria 695 · Seria 904 (modele 9**) · Seria 906 (modele 9**) · Seria 958
Valabil și pentru motoare/cutii de viteze: 924 9**, 926 9**
AR01.40-B-9202A
| Measure cylinder bores
| 01.10.2019
|
Engine
| 904.9, 906.9, 924.9, 926.9 in model 382, 384, 634, 685
|
Engine
| 904.9, 906.9, 924.9, 926.9 in model 693, 695
|
Engine
| 904.9, 906.9, 924.9, 926.9
|
Engine
| 906.9, 926.9 in model 958
|
1
| Engine block
|
2
| Dial gauge
|
3
| Gage for inside diameter
|
|
|
|
A,B
| Measuring direction in the block
|
I
| Measuring point in the reversion area of the first piston ring
|
II
| Measuring point in the center of the cylinder running surface
|
| Check
|
|
|
1
| Check the cylinder running surfaces
| Sliding surfaces should not show signs of excessive wear and/or deformation.
|
|
2
| Measure the cylinder diameter of the cylinders
|
.
| AR01.40-B-9273B
|
|
|
| .
| AR01.40-B-9291C
|
|
|
| .Cylinder's internal diameter, finishing
| *BE01.40-B-1001-02C
|
|
|
| .Out of round and taper in the cylinder/deviation from the cylinder's travel (with liner and without liner)
| *BE01.40-B-1002-02C
|
|
|
| .Maximum admissible wear at the sliding surface of the cylinders (with and without liners)
| *BE01.40-B-1003-02C
|
|
|
| Dial gage
| *001589532100
|
Number
| Designation
|
|
|
| Engine 904.9, 906.9
| Engine 924.9, 926.9
|
BE01.40-B-1001-02C
| Cylinder's internal diameter, finishing
| Normal
| Tolerance A
| mm
| 101,985...101,991
| 105,985...105,991
|
|
|
|
| Tolerance B
| mm
| 101,992...102,008
| 105,992...106,008
|
|
|
|
| Tolerance C
| mm
| 102,009...102,015
| 106,009...106,015
|
|
|
|
|
|
|
|
|
|
|
| Repair I
| Tolerance A
| mm
| 102,285...102,291
| 106,285...106,291
|
|
|
|
| Tolerance B
| mm
| 102,292...102,308
| 106,292...106,308
|
|
|
|
| Tolerance C
| mm
| 102,309...102,315
| 106,309...106,315
|
|
|
|
|
|
|
|
|
|
|
| Repair II
| Tolerance A
| mm
| 102,585...102,591
| 106,585...106,591
|
|
|
|
| Tolerance B
| mm
| 102,592...102,608
| 106,592...106,608
|
|
|
|
| Tolerance C
| mm
| 102,609...102,615
| 106,609...106,615
|
|
|
|
|
|
|
|
|
|
|
| Repair III
| Tolerance A
| mm
| 102,885...102,891
| 106,885...106,891
|
|
|
|
| Tolerance B
| mm
| 102,892...102,908
| 106,892...106,908
|
|
|
|
| Tolerance C
| mm
| 102,909...102,915
| 106,909...106,915
|
Number
| Designation
|
|
| Engine 904.9, 906.9
| Engine 924.9, 926.9
|
BE01.40-B-1002-02C
| Out of round and taper in the cylinder/deviation from the cylinder's travel (with liner and without liner)
| contact surface
| mm
| 0,012
| 0,012
|
Number
| Designation
|
|
| Engine 904.9, 906.9
| Engine 924.9, 926.9
|
BE01.40-B-1003-02C
| Maximum admissible wear at the sliding surface of the cylinders (with and without liners)
| At the reversion point of the first piston ring
| mm
| 0,1
| 0,1
|
|
|
| At the center of the cylinder
| mm
| 0,05
| 0,05
|
Documente menționate
