AR41.10-P-0085-10RT | Measure the absolute angle at the front and rear of the rear propeller shaft | ||
| Data Sheet for Measuring Inclination Angle, Form |
Workshop equipment
WE58.40-Z-1002-15A | Electronic clinometer |
WE58.40-Z-1003-15A | Electronic propeller shaft inclinometer |
WE58.40-Z-1004-15A | Electronic combination measuring instrument |
P41.10-2269-09
4 Absolute angle at front of rear propeller shaft
5 Absolute angle at rear of rear propeller shaft
P41.10-2290-09
Measurement of absolute angle 4 at front of rear propeller shaft
086a Sensor
4 Front of rear propeller shaft
6 Bolts
7 Heat shield for propeller shaft center bearing
8a Adapter for transmission
10 Cable
P41.10-2291-09
Measurement of absolute angle 5 at rear of rear propeller shaft
086a Sensor
5 Rear of rear propeller shaft
8a Adapter for transmission
10 Cable
1 Unscrew bolts (6), remove heat shield for propeller shaft center bearing
2 Attach adapter for transmission (8a) to the front of the rear propeller shaft (4) and align with the horizontal using a spirit level.
Check seat of magnetic fork at front of rear propeller shaft (4).
If the position of the sensor (086a) deviates too much from the horizontal, a fault message appears on the measuring instrument display, no value can be read off or stored.
3 Place the sensor (086a) on the support plate.
The cable (10) must point in the direction of travel (arrow), otherwise an incorrect measurement will occur.
-----------------------------------------------------------------------------------------
Ensure that the sensor (086a) is seated correctly in the bores of the support plate, otherwise an incorrect measurement will occur.
4.1 Read off absolute angle at front of rear propeller shaft (4) on the measuring instrument display and enter in the data sheet.
If the electronic inclinometer is used or if measurements are made in inclination measuring mode with the electronic articulation/propeller shaft inclinometer
The X-value must be read off on the display. Otherwise incorrect measurement results occur.
The measured value must not be stored.
The absolute angle at front of rear propeller shaft (4) may only be read off if the sensor (086a) is on standby and the displayed value is constant.
-----------------------------------------------------------------------------------------
4.2 Store the absolute angle at front of rear propeller shaft (4) in the measuring instrument.
If the electronic propeller shaft inclinometer with memory extension or the electronic articulation/propeller shaft inclinometer with memory extension is used in articulation angle measuring mode .
Save the measured value by pressing the SAVE button. After this the measurement readiness for the fifth angle is displayed.
The absolute angle at front of rear propeller shaft (4) may only be stored if the sensor (086a) is on standby and the displayed value is constant.
-----------------------------------------------------------------------------------------
5 Remove adapter for transmission (8a) from the front of the rear propeller shaft (4), attach to the rear of the rear propeller shaft (5) and move into the horizontal position using the spirit level.
Check seat of magnetic fork at rear of rear propeller shaft (5).
If the position of the sensor (086a) deviates too much from the horizontal, a fault message appears on the measuring instrument display, no value can be read off or stored.
6 Place the sensor (086a) on the support plate.
The cable (10) must point in the direction of travel (arrow), otherwise an incorrect measurement will occur.
-----------------------------------------------------------------------------------------
Ensure that the sensor (086a) is seated correctly in the bores of the support plate, otherwise an incorrect measurement will occur.
7.1 Read off absolute angle at rear of rear propeller shaft (5) on the measuring instrument display and enter in the data sheet.
If the electronic inclinometer is used or if measurements are made in inclination measuring mode with the electronic articulation/propeller shaft inclinometer
The X-value must be read off on the display. Otherwise incorrect measurement results occur.
The measured value does not have to be stored.
The absolute angle at rear of rear propeller shaft (5) may only be read off if the sensor (086a) is on standby and the displayed value is constant.
7.2 Store the absolute angle at rear of rear propeller shaft (5) in the measuring instrument.
If the electronic propeller shaft inclinometer with memory extension or the electronic articulation/propeller shaft inclinometer with memory extension is used in articulation angle measuring mode .
Save the measured value by pressing the SAVE button. After this the measurement readiness for the sixth angle is displayed.
The absolute angle at rear of rear propeller shaft (5) may only be stored if the sensor (086a) is on standby and the displayed value is constant.