ar9160p0730sc

Remove/install sensor for sidebag/windowbag

Typ ar · temat 91.60 · wersja 0100 · 2006-07-26

Dotyczy: MODEL 216.3

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 91 Fotele, leżanki, system zabezpieczenia pasażerów › 91.60 Poduszki powietrzne, system ochrony pieszych — Seria 216 (modele 3**)

EinPAS 27 Bezpieczeństwo bierne/ systemy zabezpieczające przed skutkami wypadków › 27.16 Poduszka powietrzna › 27.16.12 Czujnik/ przełącznik/ wiązka przewodów — Seria 216 (modele 3**)

AR91.60-P-0730SC

Remove/install sensor for sidebag/windowbag

14.7.06

MODEL 216.3

Remove/install sensor for sidebag/windowbag

P91.60-3303-06

1 Door sill molding panel

2 Vent grille

3 Floor Covering

4 Cable duct

5 Bolt

6 Electrical connector

A53/1 Left sidebag and windowbag sensor

A54/1 Right sidebag and windowbag sensor

X30/21 Drive train CAN voltage distributor connector

X30/28 Vehicle dynamics CAN voltage distributor connector

Remove/install

1

Remove left and right front seat and lay down toward front with wiring harness connected.

AR91.10-P-1000SC

2

Connect ground line to starter battery and to on-board electrical system battery

AR54.10-P-0003SX

3

Remove left and right door sill molding paneling (1).

4

Remove vent grille (2)

5

Loosen side paneling in rear until floor covering (3) can be loosened in this area.

AR68.30-P-4780SC

6

Loosen floor covering (3) in rear area until left sidebag and windowbag sensor (A53/1) or right sidebag and windowbag sensor (A54/1) is accessible.

7.1

Unclip drive CAN potential distributor connector (X30/21) form air duct.

When removing left sidebag and windowbag sensor (A53/1).

Do not disconnect drive CAN potential distributor connector (X30/21).

7.2

Unclip vehicle dynamics CAN potential distributor connector (X30/28) from air duct.

When removing right sidebag and windowbag sensor (A54/1).

Do not disconnect vehicle dynamics CAN potential distributor connector (X30/28).

8

Unclip cable duct (4) in rear area.

9

Lift cable duct (4) and remove bolt (5) on left sidebag and windowbag sensor (A53/1) or right sidebag and windowbag sensor (A54/1)

*BA91.60-P-1005-01L

Notes on avoiding damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

10

Disconnect electrical connector (6) and remove left sidebag and windowbag sensor (A53/1) or right sidebag and windowbag sensor (A54/1)

Installation: Insert the journals (arrows) of the left sidebag and windowbag sensor (A53/1) or right sidebag and windowbag sensor (A54/1) in the inner longitudinal member.

Notes on avoiding damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

11

Install in the reverse order

12.1

Read fault memory, erase if necessary

After replacing the left sidebag and windowbag sensor (A53/1) or right sidebag and windowbag sensor (A54/1).

Connect STAR DIAGNOSIS and read out fault memory

AD00.00-P-2000-04A

STAR DIAGNOSIS diagnosis system

*WE58.40-Z-1013-06A

Airbag

Number

Designation

Model
216

BA91.60-P-1005-01L

Screw, sidebag and windowbag sensor to B-pillar

Nm

6

Workshop equipment/MB testers (see Workshop Equipment Manual)

WE58.40-Z-1013-06A

STAR DIAGNOSIS Compact diagnosis system for passenger cars, order number 6511 1801 00

Powiązane dokumenty