4 | Windshield washer fluid reservoir |
5 | Electrical connection |
6 | Electrical connection |
7 | Expansion rivet |
8 | Cover |
9 | Electrical connection |
10 | Wiper arm |
11 | Hose |
12 | Screw |
13 | Screw |
14 | Cover |
15 | Screw |
16 | Screw |
17 | Expansion rivet |
18 | Cover |
E1 | Left lamp unit |
E2 | Right lamp unit |
E1e5 | Left turn signal lamp |
E2e5 | Right turn signal lamp |
P82.10-2141-06
E1n1 | Left xenon headlamp control unit |
E2n1 | Right xenon headlamp control unit |
Y58/1 | Purge control valve |
P82.10-2142-06
| Remove/install | ||
Danger | Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC) | Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines. | |
Danger | Risk of explosion/risk of fire caused by highly flammable materials in the vicinity of damaged xenon bulbs. Risk of injury caused by UV light, hot components on xenon headlamps and glass splinters produced by bursting xenon bulbs. Risk of poisoning caused by inhalation of mercury vapors and by swallowing of/skin contact with toxic salts and mercury compounds. | Do not touch parts conducting high voltage. Persons with active electronic implants (e.g. cardiac pacemakers) must never work on xenon headlamps. Switch off the entire lighting system. Wear insulated safety shoes, safety glasses and protective gloves. Remove highly inflammable materials from the danger zone. Ensure sufficient ventilation in the working area. | |
1 | Switch off ignition | ||
2 | Open engine hood and move to vertical position | ||
3 | Remove windscreen washer fluid reservoir (4) | Only necessary for the right lamp unit. | |
4 | Pull out expansion rivets (7) and remove cover (8) | ||
5 | Pull out expansion rivets (17) and remove cover (18) | ||
6 | Unclip turn signal light (E1e5, E2e5) and pull out towards the front | Installation: The two pins (arrows) must be pushed into the guide. | |
7 | Disconnect electrical connection (9) | ||
8 | Remove wiper arm (10) | With code 600 (Headlamp cleaning system). | |
9 | Disconnect hose (11) of headlamp cleaning system | With code 600 (Headlamp cleaning system). | |
10 | Disconnect electrical connections (5, 6) | ||
11 | Remove screws (12, 13) and carefully pull cover (14) forward | The cover remains with the seal on the vehicle. | |
12 | Remove screws (15, 16) | ||
13 | Unhook purging switchover valve (Y58/1) | Only on the left lamp unit. | |
14 | Unfasten cable tie (arrow) | Only on the right lamp unit. | |
15 | Remove lower wheel well paneling | Only on the right lamp unit. | |
16 | Detach bumper on right side | Only on the right lamp unit. | |
17 | Remove xenon headlamp control unit (E1n1, E2n1) | ||
18 | Remove lamp unit (E1, E2) with xenon headlamp control unit (E1n1, E2n1) towards the front | | |
19 | Install in the reverse order | ||
20 | Adjust zero position of headlamps using HHT | see DMAN body | |
21 | Check/correct headlamp adjustment | ||
| |||
22 | Carry out function check |
Powiązane dokumenty
- ap8210p8260a Kontrola i regulacja ustawienia reflektorów
- as0000z003501a Zagrożenie życia podczas prac przy elementach i systemach U >=30 V napięcie zmienne (AC) bądź U >=60 V napięcie zmienne
- as8210z000101a Niebezpieczeństwo wybuchu/pożaru wskutek łatwopalnych materiałów w obszarze uszkodzonych lamp ksenonowych. Niebezpieczeństwo obrażeń wskutek światła UV, gorących elementów przy reflektorach ksenonowych i odłamków szkła w prz