ar8210p1201tx

Remove/install bulbs of headlamp unit

Typ ar · temat 82.10 · wersja 0102 · 2019-11-21

Dotyczy: Model 219.3 with code 615 (Bi-xenon headlamps with active light function)

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 82 Układ elektryczny, nadwozie › 82.10 Oświetlenie zewnętrzne — Seria 219 (modele 3**)

EinPAS 30 Instalacja oświetleniowa › 30.15 Oświetlenie zewnętrzne › 30.15.40 Lampa przednia — Seria 219 (modele 3**)

AR82.10-P-1201TX

Remove/install bulbs of headlamp unit

19.11.2019

Model

219.3

with code 615 (Bi-xenon headlamps with active light function)

Remove/install bulbs of headlamp unit

P82.10-3873-09

Shown on right front lamp unit

1

Housing cover

E1

Left front lamp unit

E2

Right front lamp unit

2

High beam electrical connection

E1e1

Left high beam

E2e1

Right high beam

3

Housing cover

E1e2

Left low beam

E2e2

Right low beam

4

Retaining ring

E1e3

Left standing and parking lamp

E2e3

Right standing and parking lamp

5

Standing light and parking light holder

E1e5

Left turn signal lamp

E2e5

Right turn signal lamp

6

Turn signal lights socket

E1n2

Xenon headlamp ignition module

E2n2

Xenon headlamp ignition module

Picture no., etc.

Work notes

Danger

Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)

Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.

AS00.00-Z-0035-01A

Danger

Risk of explosion/risk of fire caused by highly flammable materials in the vicinity of damaged xenon bulbs. Risk of injury caused by UV light, hot components on xenon headlamps and glass splinters produced by bursting xenon bulbs. Risk of poisoning caused by inhalation of mercury vapors and by swallowing of/skin contact with toxic salts and mercury compounds.

Do not touch parts conducting high voltage. Persons with active electronic implants (e.g. cardiac pacemakers) must never work on xenon headlamps. Switch off the entire lighting system. Wear insulated safety shoes, safety glasses and protective gloves. Remove highly inflammable materials from the danger zone. Ensure sufficient ventilation in the working area.

AS82.10-Z-0001-01A


Do not touch the glass of the bulbs with your bare fingers; instead use a soft cloth that is free of oil and grease,
otherwise the bulbs can be damaged during operation due to overheating.


Switch off the exterior lights before changing the bulbs
in order to avoid a short circuit.

Switch off the ignition and remove the transmitter key from the EIS control unit

On vehicles with code 889 (KEYLESS-GO)

Press KEYLESS-GO start and stop button repeatedly until ignition is switched off. Remove the transmitter key from the vehicle and store at a location that is beyond the transmitter range (at least 2 m).

E1e1, E2e1

Left high beam, right high beam

Remove housing cover (1), disconnect high beam electrical connection (2) and release mounting clamp.

E1e2, E2e2

Left low beams, right low beams

Detach housing cover (3), remove xenon headlamp ignition module (E1n2, E2n2) and remove fastening ring (4).

E1e3, E2e3

Left standing light and parking light, right standing light and parking light

Turn standing light and parking light holder (5) to left and pull out of left front lamp unit (E1) or right front lamp unit (E2).

E1e5, E2e5

Left turn signal light, right turn signal light

Turn socket of turn signal light (6) to left and remove.

Powiązane dokumenty