Adjust liftgate · ar7220p0002mfx · Mercedes-Benz WIS

AR72.20-P-0002MFX

Adjust liftgate

02.10.2019

Model

247.6/7

Shown on model 247.6

1	Liftgate
2	Lock striker
X1	X-direction
X2	X-direction
Y	Y-direction
Z	Z-direction

P72.20-A026-06

P72.20-A041-09

Shown on model 247.6

5	Nuts		7	Stop buffer
6	Screw

Shown on model 247.6

3	Bolts
4	Hinge
8	Sealing foil

P72.20-A027-06

 Warning	Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.	No parts of the body or limbs should be within the operating area when the components are moving.	AS00.00-Z-0011-01A
Topical note	Notes on cavity preservation		AH97.20-P-0001-01B
	Notes on HANDS-FREE ACCESS		AH80.61-P-0001-01A
	Check
1	Check gap dimensions at liftgate (1).		AR60.00-P-0700-01MFA
		Outer tail lamp to liftgate	*BE60.00-P-1019-01MA
		Liftgate/trunk lid to inner tail lamp (top)	*BE60.00-P-1021-01MA
		Liftgate/trunk lid to inner tail lamp (bottom)	*BE60.00-P-1022-01MA
		Outside of taillamp to inside of taillamp	*BE60.00-P-1020-01MA
		Liftgate/trunk lid to bumper at rear	*BE60.00-P-1016-01MA
		Liftgate/trunk lid to side wall	*BE60.00-P-1015-01MA
		Roof spoiler to roof	*BE60.00-P-1014-01MA
		Roof spoiler to side wall	*BE60.00-P-1013-01MA
		 Feeler gauge	*129589032100
	Remove
2	Remove rear-end center-section trim.		AR68.30-P-4786MFV
3	Unscrew screws from lock striker (2) and remove lock striker (2).
4	Remove rear spoiler.	If adjustment operations are required in the Y-direction (Y) and Z-direction (Z).
		Model 247.7	AR72.20-P-4000MFA
		Model 247.6	AR72.20-P-4000MFD
5	Release roof lining until nuts (5) can be accessed.	If adjustment operations are required in X-direction (X1).
			AR68.30-P-4300MFA
6.1	Remove pneumatic springs.	Model 247.6/7 except code 890 (Automatic rear-end door)
			AR72.20-P-2832MFA
		 Do not support liftgate (1) with support. Helper required.
6.2	Remove drive units of the electrical liftgate (1).	Model 247.6/7 with code 890 (Automatic rear-end door)
			AR72.29-P-5590MFX
		 Do not support liftgate (1) with support. Helper required.
	Adjust in Y-direction (Y) and/or Z-direction (Z)
7	Remove sealing films (8).
8	Release screws (3) from left and right hinge (4).
9	Adjust liftgate (1).		AR60.00-P-0700-01MFA
		 Helper required.
		Liftgate/trunk lid to bumper at rear	*BE60.00-P-1016-01MA
		Liftgate/trunk lid to side wall	*BE60.00-P-1015-01MA
		 Feeler gauge	*129589032100
10	Tighten bolts (3).	 Helper required.
		 Bolt, hinge to liftgate	*BA72.20-P-1002-02I
	Adjust in X-direction (X1)
11	Release nuts (5) from left and right hinge (4).
12	Adjust liftgate (1).		AR60.00-P-0700-01MFA
		 Helper required.
		Liftgate/trunk lid to bumper at rear	*BE60.00-P-1016-01MA
		Liftgate/trunk lid to side wall	*BE60.00-P-1015-01MA
		 Feeler gauge	*129589032100
13	Tighten nuts (5).	 Helper required.
		 Bolt/nut, hinge to roof frame	*BA72.20-P-1001-02I
14	Clip in rear spoiler and check gap dimensions at rear spoiler to roof paneling and side wall and unclip and remove rear spoiler again.		AR60.00-P-0700-01MFA
		Model 247.6	AR72.20-P-4000MFD
		Model 247.7	AR72.20-P-4000MFA
		Roof spoiler to roof	*BE60.00-P-1014-01MA
		Roof spoiler to side wall	*BE60.00-P-1013-01MA
		 Feeler gauge	*129589032100
		If gap dimensions (Y) and gap dimension (X1) cannot be achieved,
		
		unclip rear spoiler and repeat work from operation step 8.
	Adjust in X-direction (X2)
15	Release screws (6).
16	Adjust stop buffers (7).		AR60.00-P-0700-01MFA
		Liftgate/trunk lid to side wall	*BE60.00-P-1015-01MA
		 Feeler gauge	*129589032100
17	Tighten screws (6).
	Install
18.1	Install pneumatic springs.	Model 247.6/7 except code 890 (Automatic rear-end door)
			AR72.20-P-2832MFA
		 Helper required.
18.2	Install drive units of the electrical liftgate (1).	Model 247.6/7 with code 890 (Automatic rear-end door)
			AR72.29-P-5590MFX
		 Helper required.
19	Install lock striker (2) and slightly tighten screws by hand.
	Adjust lock striker (2)
20	Adjust transitions of liftgate (1) in relation to the edges of fenders by moving lock striker (2).		AR60.00-P-0700-01MFA
		 Liftgate (1) must be flush with edges of fenders.
		Liftgate/trunk lid to bumper at rear	*BE60.00-P-1016-01MA
		Liftgate/trunk lid to side wall	*BE60.00-P-1015-01MA
		 Feeler gauge	*129589032100
21	Tighten screws on the lock striker (2).	 Bolt, lock striker to rear-end center section	*BA72.20-P-1003-02I
	Install
22	Repair paintwork damage at all open screw connections using a touch-up paint pen.
Topical note	General notes on touch-up applicators and paint spray cans		AH98.00-P-9409-06A
23	Protect liftgate (1) and roof frame in area of hinges (4) against corrosion.	If adjustment operations were required in Y-direction (Y) and in Z-direction (Z) or in X-direction (X1).
		Wax for engine compartment (400 ml spray can)	*BR00.45-Z-1018-05A
24	Install rear-end center-section trim.		AR68.30-P-4786MFV
25	Install new sealing films (8) after adjusting liftgate (1).	If adjustment operations were required in Y-direction (Y) and in Z-direction (Z).
		 Bonding surfaces must be free from dust, oil, grease, wax, dirt residues and other adhesive components. Otherwise there may be adhesion problems.
		Cleaner	*BR00.45-Z-1025-04A
26	Install rear spoiler.	If rear spoiler has been removed.
		Model 247.7	AR72.20-P-4000MFA
		Model 247.6	AR72.20-P-4000MFD
27	Attach roof lining.	If roof lining was released.
			AR68.30-P-4300MFA
	Calibrate
28	Calibrate reversing camera (B84/3) with diagnostic system.	Model 247.6/7 with code 218 (Rear view camera) except code 235 (Active Parking Assist)
			AD00.00-P-2000-06MFA
		 Calibration device	*000589012100
29	Calibrate reversing camera (B84/3) or reversing camera 360° system (B84/10) using calibration drive.	Model 247.6/7 with code 218 (Rear view camera) with code 235 (Active Parking Assist) Model 247.6/7 with code 501 (360° camera)
			AD00.00-P-2000-06MFA

Gap dimensions

Number	Designation			Model 247.6	Model 247.7
BE60.00-P-1013-01MA	Roof spoiler to side wall	Dimension "M"	mm	4,5(1)	4,5 (1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.6	Model 247.7
BE60.00-P-1014-01MA	Roof spoiler to roof	Dimension "N"	mm	5,0(1,5)	5(+1/-1,5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.6	Model 247.7
BE60.00-P-1015-01MA	Liftgate/trunk lid to side wall	Dimension "O"	mm	5(-1/+0,5)	5(1,5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.6	Model 247.7
BE60.00-P-1016-01MA	Liftgate/trunk lid to bumper at rear	Dimension "P"	mm	6(2)	6 (2)
		Dimension "P1"	mm	5(-1/+2)	4,5(1,0)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.6	Model 247.7
BE60.00-P-1019-01MA	Outer tail lamp to liftgate	Dimension "S"	mm	4(1)	4(1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.6	Model 247.7
BE60.00-P-1020-01MA	Outside of taillamp to inside of taillamp	Dimension "T"	mm	4(1)	4(1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.6	Model 247.7
BE60.00-P-1021-01MA	Liftgate/trunk lid to inner tail lamp (top)	Dimension "U"	mm	1(0,5)	1 (0,5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.6	Model 247.7
BE60.00-P-1022-01MA	Liftgate/trunk lid to inner tail lamp (bottom)	Dimension "V"	mm	1,5(1)	1,5(1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

 Liftgate

Number	Designation		Model 247
BA72.20-P-1001-02I	Bolt/nut, hinge to roof frame	Nm	15

 Liftgate

Number	Designation		Model 247
BA72.20-P-1002-02I	Bolt, hinge to liftgate	Nm	15

 Liftgate

Number	Designation		Model 247
BA72.20-P-1003-02I	Bolt, lock striker to rear-end center section	Nm	9

000 589 01 21 00

Calibration device

129 589 03 21 00

Feeler gauge

Repair materials

Number	Designation	Order number
BR00.45-Z-1018-05A	Wax for engine compartment (400 ml spray can)	A 000 986 33 70 10
BR00.45-Z-1025-04A	Cleaner	A 005 989 19 71

Powiązane dokumenty

ad0000p200006mfa
ah8061p000101a Wskazówki na temat HANDS-FREE ACCESS
ah9720p000101b Wskazówki dotyczące konserwacji profili zamkniętych
ah9800p940906a Ogólne wskazówki dotyczące lakierów w sztyfcie i w aerozolu
ar6000p070001mfa
ar6830p4300mfa
ar6830p4786mfv
ar7220p2832mfa
ar7220p4000mfa
ar7220p4000mfa
ar7220p4000mfd
ar7220p4000mfd
ar7229p5590mfx
as0000z001101a Niebezpieczeństwo zranienia przez zakleszczenie lub zmiażdżenie palców podczas demontażu, montażu i prac regulacyjnych przy pokrywach, drzwiach i oknie dachowym.