Remove/install sliding door upper carriage

AR72.16-D-7842TS

Remove/install sliding door upper carriage

18.06.2018

Model

907.6/7, 910.6

Modification notes

04.06.2018

Normalization of electric sliding door added.

Operation step 12

Shown on model 907.6 with code T55 (electrical actuation for right sliding door)

15

Release

1

Sliding door

6

Lifting device

12

Sliding base at top

13

Bolts

 Warning

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

No parts of the body or limbs should be within the operating area when the components are moving.

AS00.00-Z-0011-01A



Remove

1

Set release (15) on sliding door (1) to "MAN" position using a suitable screwdriver.

Model 907.6/7
with code T55 (Electric operation of sliding door on right)
Model 907.6/7
with code T56 (Electric operation of sliding door on left)

 This deactivates the electric drive of the sliding door (1).

2

Move sliding door (1) to a half open position.

3

Attach lifting device (6) to sliding door (1).



000 588 04 80 00 Lifting device

WS72.00-P-0018B


Handle lifting device (6) with care.
Otherwise the paint will be damaged.

4

Mark installation position of upper carriage (12) on sliding door (1).

5

Remove bolts (13).

6

Remove upper sliding carriage (12) from upper guide rail.



Install

7

Insert upper carriage (12) into upper guide rail.

8

Align upper sliding carriage (12) with markings on sliding door (1) and tighten screws (13).

 Bolt, carriage at top to sliding door

*BA72.16-N-1009-01TS

9

Remove lifting device (6) from sliding door (1).


Handle lifting device (6) with care.
Otherwise the paint will be damaged.

10

Check transition from sliding door (1) to B-pillar.

 Contour of B-pillar must align with contour of sliding door (1) or protrude by max. 1 mm.

If the transition is not correct,



adjust transition of B-pillar to sliding door (1).

AR72.16-D-1023-05TS

 Bolt, carriage to holder

*BA72.16-N-1019-01TS

 Bolt, lock striker to C-pillar

*BA72.16-N-1008-01TS

11

Set release (15) on sliding door (1) to "AUTO" position using a suitable screwdriver.

Model 907.6/7
with code T55 (Electric operation of sliding door on right)
Model 907.6/7
with code T56 (Electric operation of sliding door on left)

 This reactivates the electric drive of the sliding door (1).

12

Completely open and close sliding door (1) twice with corresponding push button switch.

Model 907.6/7
with code T55 (Electric operation of sliding door on right)
Model 907.6/7
with code T56 (Electric operation of sliding door on left)

 For the normalization of the electrical drive of the sliding door (1).
Keep push button switch pressed throughout normalization run.



Check

13

Perform function test of upper carriage (12).

 Sliding door

Number

Designation

Model 907.6/7, 910.6

BA72.16-N-1008-01TS

Bolt, lock striker to C-pillar

Nm

20

 Sliding door

Number

Designation

Model 907.6/7, 910.6

BA72.16-N-1009-01TS

Bolt, carriage at top to sliding door

Nm

23

 Sliding door

Number

Designation

Model 907.6/7, 910.6

BA72.16-N-1019-01TS

Bolt, carriage to holder

Nm

10...15