Remove/install seal for side window on front door

AR72.10-P-1906MFA

Remove/install seal for side window on front door

06.03.2020

Model

177, 247

Modification notes

08.08.2019

Remove left and right outside mirror.

Operation steps 6.2 and 26.2.

Shown on model 177.0

1

Seal

5

Exterior cover

2

Bolts

6

Outer sealing rail

3

Blind

9

Lug

4

Interior cover

 Warning

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

No parts of the body or limbs should be within the operating area when the components are moving.

AS00.00-Z-0011-01A



Remove

1

Remove left and/or right front door side window.

AR67.30-P-0008MFA

2

Remove rear section (A) of seal (1) from window guide.

3

Remove screw/bolts (2) .

4

Slide trim (3) upwards and remove towards rear from window frame.

5

Unclip interior cover (4).

Model 177


Carefully unclip interior cover (4) starting at the top.
Interior cover (4) can otherwise be damaged.

 Long wedge

*115589035900

6.1

Unclip exterior cover (5).

Model 177

 Long wedge

*115589035900

If retaining clips of exterior cover (5) are damaged



Replace exterior cover (5).

6.2

Remove left and right outside mirror.

Model 247

AR88.70-P-9000MFB

7

Remove outer sealing rail (6).

8

Remove front section (B) of seal (1) from window guide.

9

Remove section (D) above door edge.

10

Remove section (C) from door frame and remove seal (1).



Clean

11

Clean contact surfaces of seal (1) at front door.

Assembly cleaner

*BR00.45-Z-1028-04A



Check

12

Check seal (1) for damage.

If removed seal (1) is reinstalled.

If damage is identifiable



Replace seal (1).



Install

13

Slide on seal (1) starting at corner points (D, E).

14

Apply lubricant on upper section (C) of seal (1).

Lubricant, rubber assembly 1 l

*BR00.45-Z-1010-06A

15

Position upper section (C) of seal (1) at window frame.


Handle seal (1) carefully.
Seal (1) can bend very easily in upper section (C).

If seal (1) is damaged



Replace seal (1).

16

Slide trim (3) from above onto window frame.

17

Tighten bolts (2).

18

Align seal (1) and insert upper section (C) into window frame.


Handle seal (1) carefully.
Seal (1) can bend very easily in upper section (C).

 During alignment, ensure that seal (1) is flush with trim (3).

If seal (1) is damaged



Replace seal (1).

19

Coat rear section (A) of seal (1) that lies below the beltline after installation with soapy water.

 Soap solution has the required lubrication characteristics for the installation.

20

Slide rear section (A) of seal (1) downward along rear edge of side window.

21

Coat remaining area of rear section (A) of seal (1) with lubricant and insert in trim (3).

 Ensure that rear section (A) of seal (1) is in contact with trim (3) over the entire length without gap.

Lubricant, rubber assembly 1 l

*BR00.45-Z-1010-06A

22

Coat front section (B) of seal (1) that lies below beltline after installation with soapy water.

 Soap solution has the required lubrication characteristics for the installation.

23

Slide front section (B) of seal (1) downward at front edge of side window.

24

Wet remaining area of front section (B) of seal (1) with lubricant and slide into window guide.

Lubricant, rubber assembly 1 l

*BR00.45-Z-1010-06A

25

Install outer sealing rail (6).


Ensure that lug (9) is inserted into outer sealing rail (6).
Otherwise damage may occur.

26.1

Install exterior cover (5).

Model 177

26.2

Install left and right outside mirror.

Model 247

AR88.70-P-9000MFB

27

Install interior cover (4).

Model 177

28

Install front door side window.

AR67.30-P-0008MFA

 Ensure that side window runs correctly in guide of seal (1).

Repair materials

Number

Designation

Order number

BR00.45-Z-1010-06A

Lubricant, rubber assembly 1 l

A 000 989 03 67

BR00.45-Z-1028-04A

Assembly cleaner

A 000 986 56 01