1 | Side window(s) |
P67.30-2444-06
P67.30-2443-09
2 | Inner beltline sealing strip | 4 | Retaining lug | |
3 | Covers |
Warning | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
Warning | Risk of injury. Moving parts can pinch, crush or, in extreme cases even sever extremities. | No parts of the body or limbs should be within the operating area of mechanical components when moving components. | |
Caution | Risk of injury from contusions to hands if window glass is not secured | Secure window to prevent it from falling down. | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
Notes on safety-relevant components | |||
| Remove | ||
1 | Remove door trim on left and/or right. | ||
2 | Remove inner beltline sealing strip (2) on left and/or right. | ||
3 | Remove covers (3). | ||
4 | Connect electrical wiring harness of removed door trim at driver's door control unit (N69/1) and/or front-passenger door control unit (N69/2). | Helper required. | |
5 | Switch on ignition. | ||
6 | Position side window (1) on left and/or right so that retaining lugs (4) at height of access openings behind covers (3) can be accessed. | ||
7 | Switch off ignition and store transmitter key outside of transmitter range (min. 2 m). | ||
8 | Release and disconnect electrical wiring harness of removed door trim at driver's door control unit (N69/1) and/or at front-passenger door control unit (N69/2). | ||
9 | Actuate retaining lugs (4) and remove side window (1) on left and/or right upwards from window channel. | Do not damage adjacent components. | |
Helper required. | |||
| Install | ||
10 | Insert side window (1) on left and/or right into window channel until retaining lugs (4) noticeably engage. | Helper required. | |
Do not damage adjacent components. | |||
11 | Connect electrical wiring harness of removed door trim at driver's door control unit (N69/1) and/or front-passenger door control unit (N69/2). | Helper required. | |
12 | Switch on ignition. | ||
13 | Lower side window (1) on left and/or right. | ||
14 | Switch off ignition and store transmitter key outside of transmitter range (min. 2 m). | ||
15 | Release and disconnect electrical wiring harness of removed door trim from driver's door control unit (N69/1) and/or from front-passenger door control unit (N69/2). | ||
16 | Install covers (3). | ||
17 | Wet inner beltline sealing strip (2) on left and/or right with lubricant and install. | Lubricant, rubber assembly 1 l | |
18 | Install door trim on left and/or right. | ||
Normalizing | |||
19 | Normalize window lifter. | ||
|
Powiązane dokumenty
- ah0000z001901a Wskazówki dotyczące elementów wpływających na bezpieczeństwo
- ah5400p000101a Wskazówki dotyczące zapobiegania uszkodzeniom elementów elektronicznych na skutek rozładowania potencjału elektrostatycznego
- ar7210p6575mfa
- as0000z000901a Niebezpieczeństwo zakleszczenia lub zmiażdżenia, w skrajnym przypadku obcięcia kończyn podczas prac przy układach mechanicznych.
- as0000z001101a Niebezpieczeństwo zranienia przez zakleszczenie lub zmiażdżenie palców podczas demontażu, montażu i prac regulacyjnych przy pokrywach, drzwiach i oknie dachowym.
- as6700z000201a Niebezpieczeństwo obrażeń przez zmiażdżenie dłoni podczas prac przy niezabezpieczonej szybie.
- gf8200p1000a Normalizacja elektrycznie napędzanych elementów, funkcje główne