Remove/install power window on rear side window

AR67.39-P-4150QA

Remove/install power window on rear side window

19.1.10

 

Remove/install

 Danger!

Risk of injury when performing check and repair work in area of roll bar

Before working in the area of the roll bar, pull out the rear head restraints by hand.

Keep body parts out of the area where the roll bar extends.

AS91.00-Z-0003-01QA

 Danger!

Risk of injury caused by moving parts that can pinch, crush or, in extreme cases, even sever extremities

No parts of the body or limbs should be within the operating range of the mechanism when moving components.

AS00.00-Z-0009-01A

Danger!

Risk of injury caused by scraping or cutting body parts on sharp vehicle parts

Always wear protective gloves when working on or near sharp and non-deburred vehicle parts.

Deburr repair panels.

AS00.00-Z-0017-01A

1

Remove rear side window glass

AR67.30-P-4000QA

2

Remove rear passenger compartment side trim panel

AR68.30-P-4780QA

3

Remove seat belt extender

AR91.45-P-1000Q

4.1

Remove sidebag in rear

With sidebag in rear, left and right, code 293

AR91.60-P-0694QA

5

Remove bolt (1)

 Bolt on B-pillar strut

*BA77.30-P-1005-01A

6

Unscrew nut (2)

 Nut on B-pillar strut

*BA77.30-P-1006-01A

7

Remove bolt (3)

 Bolt, cross strut to B-pillar strut to soft top support

*BA77.30-P-1004-01A

8

Remove lateral strut (4)

9

Close soft top

 Complete closing procedure when rear window is in vertical position.

10

Remove bolts (9)

 Bolt on B-pillar strut

*BA77.30-P-1005-01A

11

Open soft top

 Soft top compartment lid open

12

Loosen seal for soft top compartment in assembly area

13

Loosen side wall lining in trunk and lay down to side

AR68.30-P-4600QA

14.1

Remove ATA inclination sensor

Withanti-theft alarm system (ATA), code 551

AR80.50-P-0001QA

15

Lift front inner panel (5) and remove upward.

 Installation: Ensure that spacers are seated correctly in inner wheel well.

16

Disconnect left rear power window motor connector (X16/2), right rear power window motor connector (X16/3)

17

Unclip rub strip (6) from rear fender

 Mounting wedge

*110589035900

18

Remove textile adhesive tape

 Replace if necessary.

*BR00.45-Z-1062-02A

19

Unscrew nuts of power window (7)

 Jam nut for power window mount in center pillar

*BA67.39-P-1002-01A

 Socket wrench

*209589000900

20

Take out power window (8) through access opening

21

Install in the reverse order

22

Perform basic setting for rear side power window

AR67.30-P-4200-06QA

23

Perform basic programming

AR00.19-P-0200Q

24

Read out fault memory and erase

 Stored faults which may be caused by assembly work, test work, removed lines or a simulation, must be processed and erased in fault memories after completing the work.



Connect STAR DIAGNOSIS and read out fault memory

AD00.00-P-2000-04A

STAR DIAGNOSIS Compact diagnosis system for passenger cars

25

Carry out function check

Number

Designation

Model 209.4

BA77.30-P-1004-01A

Bolt, cross strut on B-pillar strut to soft top bearing

Nm

10 (2)

BA77.30-P-1005-01A

Bolt on B-pillar strut

M616

Nm

10 (2)

M816

Nm

20 (2)

BA77.30-P-1006-01A

Nut on B-pillar strut

Nm

20 (2)

Number

Designation

Model
209

BA67.39-P-1002-01A

Locknut for electric power window mount in center pillar

Nm

9

Number

Designation

Order number

BR00.45-Z-1062-02A

Adhesive fabric tape

A 007 989 28 85