P67.30-2447-09
Shown on model 177.0 |
1 | Side window(s) | 3 | Inner beltline sealing strip | |
2 | Cover | 4 | Retaining lug |
Caution | Risk of injury from contusions to hands if window glass is not secured | Secure window to prevent it from falling down. | |
Warning | Risk of injury. Moving parts can pinch, crush or, in extreme cases even sever extremities. | No parts of the body or limbs should be within the operating area of mechanical components when moving components. | |
Warning | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
Notes on safety-relevant components | |||
| Remove | ||
1 | Remove left or right door trim. | ||
2 | Remove left or right inner beltline sealing strip (3). | ||
3 | Remove cover (2). | ||
4 | Connect electrical wiring harness of removed door trim with left rear door control unit (N69/3) or with right rear door control unit (N69/4). | Helper required. | |
5 | Switch on ignition. | ||
6 | Position left or right side window (1) such that the retaining lug (4) at the level of the access opening, behind the cover (2), is accessible. | ||
7 | Switch off ignition and store transmitter key outside of transmitter range (min. 2 m). | ||
8 | Release and disconnect electrical wiring harness of removed door trim from left rear door control unit (N69/3) or from right rear door control unit (N69/4). | ||
9 | Actuate retaining lug (4) and remove left or right side window (1) from window channel in upward direction. | Do not damage adjacent component parts. | |
Helper required. | |||
| Install | ||
10 | Insert left or right side window (1) into window channel until retaining lug (4) engages noticeably. | Helper required. | |
Do not damage adjacent component parts. | |||
11 | Install cover (2). | ||
12 | Connect electrical wiring harness of removed door trim with left rear door control unit (N69/3) or with right rear door control unit (N69/4). | Helper required. | |
13 | Switch on ignition. | ||
14 | Move left or right side window (1) down. | ||
15 | Switch off ignition and store transmitter key outside of transmitter range (min. 2 m). | ||
16 | Release and disconnect electrical wiring harness of removed door trim from left rear door control unit (N69/3) or from right rear door control unit (N69/4). | ||
17 | Wet left or right inner beltline sealing strip (3) with lubricant and install. | Lubricant, rubber assembly 1 l | |
18 | Install left or right door trim. | ||
Normalizing | |||
19 | Normalize window lifter. | ||
|
Powiązane dokumenty
- ah0000z001901a Wskazówki dotyczące elementów wpływających na bezpieczeństwo
- ah5400p000101a Wskazówki dotyczące zapobiegania uszkodzeniom elementów elektronicznych na skutek rozładowania potencjału elektrostatycznego
- ar7212p1011mfa
- as0000z000901a Niebezpieczeństwo zakleszczenia lub zmiażdżenia, w skrajnym przypadku obcięcia kończyn podczas prac przy układach mechanicznych.
- as0000z001101a Niebezpieczeństwo zranienia przez zakleszczenie lub zmiażdżenie palców podczas demontażu, montażu i prac regulacyjnych przy pokrywach, drzwiach i oknie dachowym.
- as6700z000201a Niebezpieczeństwo obrażeń przez zmiażdżenie dłoni podczas prac przy niezabezpieczonej szybie.
- gf8200p1000a Normalizacja elektrycznie napędzanych elementów, funkcje główne