ar6430d573102ts

Prepare complete outer corner pillar paneling upper section

Typ ar · temat 64.30 · wersja 0100 · 2018-06-07

Dotyczy: Model 907.6/7, 910.6

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 64 Ściana tylna i tył pojazdu › 64.30 Poszycie naroża — Seria 907 (modele 6**, 7**) · Seria 910 (modele 6**)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.31 Ściana tylna/ tył pojazdu › 35.31.30 Ściana tylna/ tył pojazdu — Seria 907 (modele 6**, 7**) · Seria 910 (modele 6**)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.45 Słupek — Seria 907 (modele 6**, 7**) · Seria 910 (modele 6**)

AR64.30-D-5731-02TS

Prepare complete outer corner pillar paneling upper section

Model

907.6/7, 910.6

Repair materials

Number

Designation

Order number

BR00.45-Z-1056-07A

1K-zinc dust paint

A 000 986 28 00

Additional information can be found in the superordinate service document.
The safety information in the superordinate KD document must be observed.

The next steps are shown on model 907.633 with code D03 (roof and rear-end doors, high version) on the right component part and must be carried out in the same way in the event of damage to the left side of the vehicle.

Prepare complete outer corner pillar paneling upper section

1

Mark separating point at outer corner pillar paneling section (1) (area A).


Mark separating point along edge.



2

Disconnect separating point from outer corner pillar paneling section (1) (area A).


Commercially available devices/tools
Body power jigsaw



3

Mark separating point at outer corner pillar paneling section (1) (area B).


Take over dimension for separating point from vehicle.



4

Disconnect separating point from outer corner pillar paneling section (1) (area B).


Commercially available devices/tools
Body power jigsaw



5

Dispose of cut-off pieces.


D64.30-1231-12

Prepare complete outer corner pillar paneling upper section

6

Punch holes in outer corner pillar paneling section (1) with a diameter of 6 mm (areas C and D).


Commercially available devices/tools
Hole punching pliers 6 mm



7

Grind mating surfaces in cross-hatched areas and around holes (areas C and D) down to bare metal.


Sand down spot weld flanges to bare metal on both sides.


Commercially available devices/tools
Rotary wire brush



8

Remove shavings.


Commercially available devices/tools
Wet and dry vacuum cleaner



9

Zinc dust paint to insides of spot weld flanges.


D64.30-1243-12

Prepare complete outer corner pillar paneling upper section

10

Mark separating point at inner corner pillar paneling section (2) (area E).


Take over dimension for separating point from vehicle.



11

Disconnect separating point from inner corner pillar paneling section (2) (area E).


Commercially available devices/tools
Body power jigsaw



12

Dispose of the leftover piece that has been separated off.



13

Punch holes in inner corner pillar paneling section (2) with a diameter of 6 mm (areas F, G, and H).


Commercially available devices/tools
Hole punching pliers 6 mm


D64.30-1244-12

Prepare complete outer corner pillar paneling upper section

14

Grind mating surfaces down to bare metal in cross-hatched areas and around holes.


Sand down spot weld flanges to bare metal on both sides.


Commercially available devices/tools
Rotary wire brush



15

Remove shavings.


Commercially available devices/tools
Wet and dry vacuum cleaner



16

Zinc dust paint to insides of spot weld flanges.


D64.30-1245-12

Prepare complete outer corner pillar paneling upper section

17

Punch holes in lower outer corner pillar paneling section (3) with a diameter of 6 mm (area I).


Commercially available devices/tools
Hole punching pliers 6 mm



18

Grind mating surfaces in cross-hatched area and around holes (area I) down to bare metal.


Sand down spot weld flanges to bare metal on both sides.


Commercially available devices/tools
Rotary wire brush



19

Remove shavings.


Commercially available devices/tools
Wet and dry vacuum cleaner



20

Zinc dust paint to insides of spot weld flanges.


D64.30-1246-01