P64.20-3747-06
Shown on model 171
1 Spare tire well
2 Rear crossmember
3 Longitudinal member connection element
4 End plate
| Removing | ||
Danger! | Risk of death caused by high voltage used for electric welding. Risk of explosion caused by welding in the area of highly inflammable materials. Risk of injury caused by welding splatter and UV light while welding. Risk of poisoning caused by inhaling welding fumes. | Use insulating mats. Wear protective clothing, safety glasses and protective mask. Remove highly inflammable materials from the hazard area. Use air extractor system. | |
Danger! | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer. | |
Danger! | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels. | |
Danger! | Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel and risk of injury to eyes and skin caused by contact with fuel | No fire, sparks, open flames or smoking. Wear protective clothing when handling fuel. | |
| Measures for preventing damage to components when performing electric welding and soldering work | ||
| General information on body repair | ||
| General information on riveting | ||
| General information on MB materials | ||
1 | Remove detachable parts in area to be repaired | ||
2 | Cover all detachable parts remaining in vehicle with fire-resistant welding protection blanket | Welding protective blanket gotis://K_60-65_23.0 | |
3 | Equip straightening bench with module members, cross members and straightening tool set. | Observe enclosed set-up plans. | |
Straightening tool set, passenger cars (Celette) gotis://K_60-65_02.0 | |||
Straightening system, passenger cars ( Car Bench) gotis://K_60-65_03.0 | |||
4 | Place vehicle on straightening bench lift and fasten | Two-column lift 3.0 - -3.5 t electromechanical gotis://H_00.1_01.0 | |
Two-post lifting platform, 2.5 - 3.5 t electrohydraulic gotis://H_00.1_01.1 | |||
5 | Remove lower rear center section | ||
6 | Remove rear fender | ||
7 | Separate rear cross member (2), spare tire well (1) and longitudinal member connection element (3) | Round wire brush gotis://K_58.3_06.0 | |
Weld-spot milling machine gotis://K_58.1_02.0 | |||
Body jig saw gotis://K_58.1_01.0 | |||
Wet and dry vacuum cleaner gotis://P_00.12_06.0 | |||
Zinc dust paint suitable for spot welding | |||
8 | Prepare rear cross member (2), spare tire well (1) and longitudinal member connection element (3) | Round wire brush gotis://K_58.3_06.0 | |
Vice grip pliers (standard) gotis://K_58.3_04.2 | |||
Zinc dust paint suitable for spot welding | |||
| Install | ||
9 | Install rear cross member (2), spare tire well (1) and longitudinal member connection element (3) and weld in | Straightening tool set, passenger cars (Celette) gotis://K_60-65_02.0 | |
Straightening system, passenger cars ( Car Bench) gotis://K_60-65_03.0 | |||
Multifunction device (spot welding) gotis://K_60-65_15.0 | |||
MIG-MAG inert gas welder gotis://K_60-65_17.1 | |||
Pneumatic-mechanical blind rivet tool gotis://K_58.3_10.2 | |||
Vice grip pliers (standard) gotis://K_58.3_04.2 | |||
Round wire brush gotis://K_58.3_06.0 | |||
Manual temporary fastener, 6.35 mm gotis://K_58.3_10.0 | |||
Zinc dust paint suitable for spot welding | |||
Blind rivet 6.512.5 | |||
10 | Release vehicle from straightening bench, lift vehicle and remove straightening bench | Two-column lift 3.0 - -3.5 t electromechanical gotis://H_00.1_01.0 | |
Two-post lifting platform, 2.5 - 3.5 t electrohydraulic gotis://H_00.1_01.1 | |||
11 | Clean weld joints and sheet metal flanges with rotary wire brush | Round wire brush gotis://K_58.3_06.0 | |
12 | Install rear fender | ||
13 | Remove lower rear center section |
Repair materials
Number | Designation | Order number |
BR00.45-Z-1001-07A | Zinc dust paint suitable for spot welding | A 000 986 34 42 |
BR00.45-Z-1012-13A | Blind rivet 6.512.5 | A 004 990 16 97 |
Powiązane dokumenty
- ah6000n000101a Ogólne wskazówki dotyczące napraw nadwozia
- ah6000p000102a Środki zapobiegające uszkodzeniom pojazdu lub jego elementów podczas spawania elektrycznego i lutowania
- ah6000p000301n Ogólne wskazówki dotyczące nitowania
- ah9800p940903a Informacje ogólne dotyczące środków MB
- ar6350p1400v Wymiana kompletnego błotnika tylnego
- ar6420p1000v
- ar6420p120001v
- ar6420p120002v
- ar6420p120035v
- as0000z000701a Zagrożenie dla życia przez wysokie napięcie przy spawaniu elektrycznym. Niebezpieczeństwo wybuchu podczas spawania w pobliżu materiałów łatwopalnych. Niebezpieczeństwo urazu na skutek odprysków przy spawaniu oraz promieniowania u
- as0000z001001a Zagrożenie życia na skutek ześlizgnięcia lub spadnięcia pojazdu z podnośnika.
- as0000z001701a Niebezpieczeństwo obrażeńo elementy pojazdu o ostrych krawędziach.
- as4700z000101a Niebezpieczeństwo wybuchu wskutek zapalenia, niebezpieczeństwo zatrucia wskutek wdychania i połknięcia paliwa oraz niebezpieczeństwo obrażeń wskutek kontaktu skóry i oczu z paliwem.