P63.20-4870-06
1 Inner A-pillar
| Removing | ||
Danger! | Risk of death caused by high voltage used for electric welding. Risk of explosion caused by welding in the area of highly inflammable materials. Risk of injury caused by welding splatter and UV light while welding. Risk of poisoning caused by inhaling welding fumes. | Use insulating mats. Wear protective clothing, safety glasses and protective mask. Remove highly inflammable materials from the hazard area. Use air extractor system. | |
Danger! | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer. | |
Danger! | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels. | |
| Measures for preventing damage to components when performing electric welding and soldering work | ||
| General information on body repair | ||
| Notes on paintwork repairs | ||
| General information on MB materials | ||
1 | Remove detachable parts in area to be repaired | ||
2 | Cover all detachable parts remaining in vehicle with fire-resistant welding protection blanket | Welding protective blanket gotis://K_60-65_23.0 | |
3 | Equip straightening bench with module members, cross members and straightening tool set. | Observe set-up plans provided. | |
Passenger car straightening system (Celette) gotis://K_60-65_02.0 | |||
Passenger car straightening system (Car Bench) gotis://K_60-65_03.0 | |||
4 | Place vehicle on straightening bench and fasten | Two-post lifting platform, 3.0 - 3.5 t electromechanical gotis://H_00.1_01.0 | |
Two-post lifting platform, 2.5 - 3.5 t electrohydraulic gotis://H_00.1_01.1 | |||
5 | Remove A-pillar with side longitudinal member | ||
6 | Separate inner A-pillar (1) | Round wire brush gotis://K_58.3_06.0 | |
Weld-spot milling machine gotis://K_58.1_02.0 | |||
Wet and dry vacuum cleaner gotis://P_00.12_06.0 | |||
Zinc dust paint suitable for spot welding | |||
7 | Prepare inner A-pillar (1) | Round wire brush gotis://K_58.3_06.0 | |
Zinc dust paint suitable for spot welding | |||
| Install | ||
8 | Install inner A-pillar (1) | ||
Portal frame | |||
Welding device | |||
Straightening bracket set, passenger cars, cross-country vehicles (Celette) gotis://K_60-65_02.0 | |||
Straightening system, passenger cars (Car Bench) gotis://K_60-65_03.0 | |||
Multifunction device (spot welding) gotis://K_60-65_15.0 | |||
MIG-MAG inert gas welder gotis://K_60-65_17.1 | |||
Vice grip pliers (standard) gotis://K_58.3_04.2 | |||
Round wire brush gotis://K_58.3_06.0 | |||
Wet and dry vacuum cleaner gotis://P_00.12_06.0 | |||
9 | Install A-pillar with side longitudinal member | ||
10 | Clean weld joints and sheet metal flanges with rotary wire brush | Round wire brush gotis://K_58.3_06.0 | |
11 | Remove welding protection blankets | ||
12 | Clean repair area | Wet and dry vacuum cleaner gotis://P_00.12_06.0 | |
Danger! | Risk of explosion caused by paint vapors igniting. Risk of poisoning caused by inhaling paint vapors. | No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and skin cream. Ensure that the area is well ventilated. | |
13 | Prime repair area using primer filler | Use only primer filler approved by Daimler AG. | |
http://portal.aftersales.i.daimler.com | |||
14 | Carry out seam sealing after repairs | Supplement standard seals with sealant. | |
Danger! | Risk of explosion caused by paint vapors igniting. Risk of poisoning caused by inhaling paint vapors. | No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and skin cream. Ensure that the area is well ventilated. | |
15 | Paint repair areas and adjacent surfaces | Use only paints approved by Daimler AG. | |
http://portal.aftersales.i.daimler.com | |||
16 | Apply additional cavity preservation | ||
17 | Install all detachable body components in area to be repaired |
171 589 00 23 00
Welding device
Portal frame
129 589 03 23 00
Repair materials
Number | Designation | Order number |
BR00.45-Z-1001-07A | Zinc dust paint suitable for spot welding | A 000 986 34 42 |
Powiązane dokumenty
- ah6000n000101a Ogólne wskazówki dotyczące napraw nadwozia
- ah6000p000102a Środki zapobiegające uszkodzeniom pojazdu lub jego elementów podczas spawania elektrycznego i lutowania
- ah9800p940802a Wskazówki dotyczące napraw powłok lakierniczych
- ah9800p940903a Informacje ogólne dotyczące środków MB
- ar6320p110601v
- ar6320p110602v
- ar6320p110603v
- ar6320p1150v
- ar9710p4000w
- ar9720p1500w
- as0000z000701a Zagrożenie dla życia przez wysokie napięcie przy spawaniu elektrycznym. Niebezpieczeństwo wybuchu podczas spawania w pobliżu materiałów łatwopalnych. Niebezpieczeństwo urazu na skutek odprysków przy spawaniu oraz promieniowania u
- as0000z001001a Zagrożenie życia na skutek ześlizgnięcia lub spadnięcia pojazdu z podnośnika.
- as0000z001701a Niebezpieczeństwo obrażeńo elementy pojazdu o ostrych krawędziach.
- as9800z000201a Niebezpieczeństwo eksplozji w wyniku zapalenia się oparów lakierniczych. Niebezpieczeństwo zatrucia na skutek wdychania oparów lakierniczych.