ar6310d004001ts

Cut inner section of rear side wall paneling up to window cutout

Typ ar · temat 63.10 · wersja 0100 · 2019-02-14

Dotyczy: Model 907.6 with code W22 (Fixed window, center left) with code W23 (Fixed window, center right) Model 907.6 with code W24 (Sliding window center left) with code W25 (Sliding window center right) Model 907.6 with code W27 (Fixed window, rear left) with code W28 (Fixed window at rear right) Model 907.6 with code W34 (Sliding window rear left) with code W35 (Sliding window rear right) Model 907.7

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 63 Ściana boczna › 63.10 Ściana boczna — Seria 907 (modele 6**, 7**)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.35 Błotnik/ ściana boczna — Seria 907 (modele 6**, 7**)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.38 Poszycie z lewej strony — Seria 907 (modele 6**, 7**)

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.39 Poszycie z prawej strony — Seria 907 (modele 6**, 7**)

AR63.10-D-0040-01TS

Cut inner section of rear side wall paneling up to window cutout

Model

907.6

with code W22 (Fixed window, center left)

with code W23 (Fixed window, center right)

Model

907.6

with code W24 (Sliding window center left)

with code W25 (Sliding window center right)

Model

907.6

with code W27 (Fixed window, rear left)

with code W28 (Fixed window at rear right)

Model

907.6

with code W34 (Sliding window rear left)

with code W35 (Sliding window rear right)

Model

907.7

Repair materials

Number

Designation

Order number

BR00.45-Z-1056-07A

1K-zinc dust paint

A 000 986 28 00

Additional information can be found in the superordinate service document.

The safety information in the superordinate service document must be observed.

The next steps are shown on the left side of the vehicle for model 907.633 and must be performed in a similar manner for vehicles with damage on the right side of the vehicle.

Cut inner section of rear side wall paneling up to window cutout

D63.10-A021-09

a

Dimension (approx. 170 mm)

b

Dimension (approx. 170 mm)

1

Mark separating points on inside part of sidewall (1) (areas A and B).

Observe dimensions (A, B).

2

Cut separating points on inside part of sidewall (1) (areas A and B).

Commercially available devices/tools
Body power jigsaw

3

Expose spot welds on inside part of sidewall (1) (area G).

Commercially available devices/tools
Rotary wire brush

4

Cut off spot welds on inside part of sidewall (1) (area G).

Commercially available devices/tools
Spot weld milling machine

5

Mark separating points on reinforcement (2) (area C) and reinforcement (3) (area D).

6

Cut separating points on reinforcement (2) (area C) and reinforcement (3) (area D).

Commercially available devices/tools
Body power jigsaw

7

Expose spot welds on reinforcement (2) (area F) and reinforcement (3) (area E).

Commercially available devices/tools
Rotary wire brush

8

Cut off spot welds on reinforcement (2) (area F) and reinforcement (3) (area E).

Commercially available devices/tools
Spot weld milling machine

Cut inner section of rear side wall paneling up to window cutout

D63.10-A022-09

9

Mark separating point on inside part of sidewall (1) (area J).

10

Cut separating point on inside part of sidewall (1) (area J).

Commercially available devices/tools
Body power jigsaw

11

Expose spot welds on inside part of sidewall (1) (areas H, H1 and I).

Commercially available devices/tools
Rotary wire brush

12

Cut off spot welds on inside part of sidewall (1) (areas H, H1 and I).

Commercially available devices/tools
Spot weld milling machine

13

Remove damaged inside part of sidewall (1).

Cut inner section of rear side wall paneling up to window cutout

14

Expose spot welds on remaining section (4) (area L) and remaining section (5) (area K).


Commercially available devices/tools
Rotary wire brush



15

Cut off spot welds on remaining section (4) (area L) and remaining section (5) (area K).


Commercially available devices/tools
Spot weld milling machine



16

Remove remaining sections (4, 5).


D63.10-A023-06

Cut inner section of rear side wall paneling up to window cutout

17

Grind mating surfaces down to bare metal in cross-hatched areas and around hole.


Sand down spot weld flanges to bare metal on both sides.


Commercially available devices/tools
Rotary wire brush



18

Remove shavings and milling chips.


Commercially available devices/tools
Wet and dry vacuum cleaner



19

Zinc dust paint to insides of spot weld flanges.


D63.10-A024-06