S61.10-4689-09
1 | Rear floor |
Danger | Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC) | Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.Model 447 with engine 780 | |
Danger | The high voltage used for electric welding presents a lethal hazard. Risk of explosion from welding in areas close to highly inflammable materials. Risk of injury from weld splatter and UV-light when welding. Risk of poisoning from inhaling welding gases | Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly inflammable materials from the hazard area. Use air extraction system. | |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Topical note | Notes on battery | ||
Topical note | General information on vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system as well as personal protective equipment | Model 447 with engine 780 | |
Topical note | Special instructions for lifting and supporting vehicle | ||
Topical note | General information on body repair | ||
Topical note | Measures for preventing damage to components when performing electric welding and soldering work | ||
General information on MB materials | |||
| Remove | ||
1 | Remove all detachable parts in area of repair point. | ||
2 | Cover all detachable parts remaining in vehicle with welding protection blankets. | Commercially available devices/tools | |
3 | Remove left and right inner rear wheel well. | ||
4 | Cut off rear floor (1). | ||
| 000 588 00 84 00 Heat gun | ||
Commercially available devices/tools | |||
WIS Service Media | |||
5 | Prepare rear floor (1) for installation. | ||
Commercially available devices/tools | |||
WIS Service Media | |||
| Install | ||
6 | Install rear floor (1) and weld in. | ||
| 000 588 02 84 00 Welder | ||
Commercially available devices/tools | |||
WIS Service Media | |||
7 | Remove welding protection blankets. | Commercially available devices/tools | |
8 | Install left and right inner rear wheel well. | ||
9 | Apply damping to the rear floor. | ||
10 | Install all detachable parts in area of repair point. |
Powiązane dokumenty
- ah0000z030001a Ogólne wskazówki dotyczące pojazdów z instalacją wysokiego napięcia i/lub akumulatorem litowo-jonowym i/lub gazowym systemem napędu oraz osobistego wyposażenia ochronnego
- ah0060n010001a Wskazówki dotyczące podnoszenia pojazdu, ustawiania na podporach
- ah5410p000101a
- ah5410p000101a Wskazówki dotyczące akumulatora
- ah6000n000101a Ogólne wskazówki dotyczące napraw nadwozia
- ah6000p000102a Środki zapobiegające uszkodzeniom pojazdu lub jego elementów podczas spawania elektrycznego i lutowania
- ah9800p940903a Informacje ogólne dotyczące środków MB
- ar6000s1751e
- ar6110s574801e
- ar6110s574802e
- ar6110s574803e
- ar6310s0670e
- as0000z000701a Zagrożenie dla życia przez wysokie napięcie przy spawaniu elektrycznym. Niebezpieczeństwo wybuchu podczas spawania w pobliżu materiałów łatwopalnych. Niebezpieczeństwo urazu na skutek odprysków przy spawaniu oraz promieniowania u
- as0000z001001a Zagrożenie życia na skutek ześlizgnięcia lub spadnięcia pojazdu z podnośnika.
- as0000z001701a Niebezpieczeństwo obrażeńo elementy pojazdu o ostrych krawędziach.
- as0000z003501a Zagrożenie życia podczas prac przy elementach i systemach U >=30 V napięcie zmienne (AC) bądź U >=60 V napięcie zmienne
- ws5400p0049b
- ws6000p0022k