ar4625p3015we

Remove/install hydraulic line of power steering

Typ ar · temat 46.25 · wersja 0101 · 2012-02-07

Dotyczy: MODEL 172 with ENGINE 271 pressure line

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 2 Podwozie › 46 Układ kierowniczy › 46.25 Hydrauliczny/ elektrohydrauliczny układ kierowniczy — Seria 172

EinPAS 22 Układ kierowniczy › 22.15 Wspomaganie kierownicy › 22.15.13 Przewód sztywny/elastyczny/zawór — Seria 172

Dotyczy też silników/skrzyń biegów: 271 ***

AR46.25-P-3015WE

Remove/install hydraulic line of power steering

3.2.12

MODEL 172 with ENGINE 271
pressure line

Remove/install hydraulic line of power steering

P46.25-2189-09

1 Pressure line

2 Air intake hose

3 Expansion reservoir

7 Oil pan

8 Screw

9 Rack-and-pinion steering

4 Screw

5 Power steering pump

6 Screw

Remove/install

Danger!

Risk of injury to skin or eyes caused by hydraulic fluid spraying out under high pressure. Risk of poisoning caused by swallowing hydraulic fluid

Depressurize hydraulic system completely before starting any work on system. Wear protective clothing and safety glasses.

AS00.00-Z-0013-01A

1

Open engine hood

AR88.40-P-1000V

2

Remove air intake hose (2)

3

Suction off oil out of power steering expansion reservoir (3)

The area surrounding the separation point should be cleaned thoroughly before opening the hydraulic system. Even the smallest dirt particles, introduced into the hydraulic components, can lead to malfunctions and a total failure of the hydraulic system.

Hand pump

*210589007100

4

Remove bolt (4) and detach pressure line (1) from
power steering pump (5)

Collect escaping oil with a rag and plug line connections.

Set of stop plugs

*129589009100

Installation: Replace sealing ring.

*BA46.30-P-1004-01R

5

Remove center section of the lower engine compartment paneling

Installation: Only install engine compartment paneling after the leak test.

AR61.20-P-1105W

6

Remove bolt (6) and detach pressure line (1) from oil pan (7)

*BA46.30-P-1006-01R

7

Remove bolt (8) and detach pressure line (1) from rack-and-pinion steering (9) then remove downwards

Collect escaping oil with a rag and plug line connections.

Set of stop plugs

*129589009100

Installation: Replace sealing ring.

*BA46.20-P-1001-01F

8

Install in the reverse order

9

Fill and bleed power steering pump (5).

AR46.30-P-0010V

10

Check oil level in expansion reservoir (3) of power steering, correct if necessary

AP46.00-P-4611V

Steering gear

Number

Designation

Model
172

BA46.20-P-1001-01F

Bolt, oil line retaining plate to rack-and-pinion steering

Nm

18

Power steering pump

Number

Designation

Model
172 without
engine 152

BA46.30-P-1004-01R

Attachment, high pressure expansion hose of rack-and-pinion steering to power steering pump or tandem pump

Union nut

Nm

40

Banjo bolt

Nm

-

Bolt M8

Nm

18

BA46.30-P-1006-01R

Bracket from high-pressure line/low-pressure line to oil pan

Nm

10

Remove/install hydraulic line of power steering
Remove/install hydraulic line of power steering

210 589 00 71 00

Hand pump

Set of stop plugs

129 589 00 91 00

Powiązane dokumenty