Perform wheel alignment check

AR40.20-P-0200MCE

Perform wheel alignment check

25.9.14

MODEL

451.3/4

with recording the vehicle level

Measuring, adjusting

1

Check tire pressure, correct if necessary



AP40.15-P-4061MCC

2

Perform initial measurement

 Carry out measurements according to information provided by measuring device manufacturer.
Perform measurements on unladen vehicle with fuel tank 90 % full.

Camber

*BE40.20-P-1001-06C

Caster

*BE40.20-P-1002-06C

Total toe at front axle

*BE40.20-P-1001-07B

Toe-out angle with inner wheel steered through 20°

*BE40.20-P-1001-08C

Rear axle camber

*BE40.20-P-1001-09U

Total rear axle toe

*BE40.20-P-1001-10F

Driveline angle

*BE40.20-P-1001-21A

3

Record vehicle level at front and rear axles using electronic inclinometer

AR40.20-P-0303MCC

4

Determine toe of front axle from the table

AR40.20-P-0322-11MCC

5

Adjust front axle toe

AR40.20-P-0323-02MCC

Total toe at front axle

*BE40.20-P-1001-07B

 Jam nut at tie rod

*BA46.40-P-1002-01F

 Open-ended socket wrench

*450589010900

6

Perform final measurement

Camber

*BE40.20-P-1001-06C

Caster

*BE40.20-P-1002-06C

Total toe at front axle

*BE40.20-P-1001-07B

Toe-out angle with inner wheel steered through 20°

*BE40.20-P-1001-08C

Rear axle camber

*BE40.20-P-1001-09U

Total rear axle toe

*BE40.20-P-1001-10F

Driveline angle

*BE40.20-P-1001-21A

Should after adjusting the front axle toe other values are still outside the tolerance range or the steering wheel is not on straight:



Perform advanced chassis alignment

AR40.20-P-0250MCE

7

Calibrate steering angle sensor using diagnostic system



AD00.00-P-2000-04MCC

Inspection and setting data of front axle camber/caster

Number

Designation

MODEL 451.3/4

BE40.20-P-1001-06C

Camber

with 0° wheel toe

+0° 18' (0° 42')

Max. difference left to right

0° 30'

Check values for front axle toe

Number

Designation

Model 451.3/4

BE40.20-P-1001-07B

Total toe at front axle

°

+0° 36' (0° 10')

Check values for toe-out angle

Number

Designation

MODEL 451.3/4

BE40.20-P-1001-08C

Toe-out angle with inner wheel steered through 20°

°

–1° 36' ( 0° 30')

Inspection and setting data of rear axle camber

Number

Designation

MODEL 450.3/4, 451.3/4, 452.3/4

BE40.20-P-1001-09U

Rear axle camber

°

–2° 00' (0° 30')

Check values for rear axle toe

Number

Designation

MODEL 451.3/4

BE40.20-P-1001-10F

Total rear axle toe

°

+0° 00' (0° 18')

Test values for driveline angle

Number

Designation

MODEL 451.3/4

BE40.20-P-1001-21A

Driveline angle

°

+0° 0' (0° 24')

Inspection and setting data of front axle camber/caster

Number

Designation

MODEL 451.3/4

BE40.20-P-1002-06C

Caster

with 0° wheel toe

+7° 50' (0° 30')

 Tie rod

Number

Designation

MODEL 451.3/4

BA46.40-P-1002-01F

Jam nut at tie rod

Nm

50