Check and adjust front axle toe

AR40.20-D-0323TST

Check and adjust front axle toe

08.02.2019

Model

907

with code IT5 (5.0 tonner)

except code IT3 (3,0 tonner)

except code IT4 (3,5 tonner)

except code IT9 (4.0 tonner)

except code ZU7 (National version for Canada)

except code ZU8 (National version for USA)

055

Holding device

Illustration of left side of vehicle

1

Ball head

3

Jam nut

4

Tie rod

030

Wheel spreader

Notes on repair work on suspension components

AH00.00-P-0100-01A



Check

1

Check preconditions for wheel alignment.

AR40.20-D-0050TS

 Determine difference between the inner and outer tire tread channel depth here too.

2.1

Determine front-axle level using the transverse control arm angle bracket with electronic inclinometer.

When measuring with electronic inclinometer.

AR40.20-D-6870TS

2.2

Determine front-axle level through actual front-axle load.

When measuring without electronic inclinometer.

 Commercially available devices/tools
Wheel load scales

3

Set steering gear to center position.

AR46.20-D-0500-01TS

Topical note

Notes on carrying out repair work in the vehicle interior

AH68.00-N-0001-01S

 Retainer device

*129589012100

 Tensioning nut

*906589002100

If the center position is incorrect,



remove steering wheel, shift by max. one tooth then mount steering wheel again.

Remove/install steering wheel

AR46.10-D-0100TS

4

Install wheel spreader (030), as shown, in direction of travel at front on insides of wheel.

 The elastic bearing of the lower transverse control arm and steering linkage produce a correspondingly large toe value that is reduced to the correct dimension in the ready-to-drive condition.

5

Perform initial measurement.

AR40.20-D-0200TS

 The actual suspension data such as camber, toe, steering axis inclination, caster and the toe-out angle are determined here.

6

Check toe using front-axle level and assign to value in table.

 Observe permissible difference in front axle toe-in between right and left sides of the vehicle.

 If the determined difference between the inner and outer tread groove depth is greater than 2 mm, then the values for major wear on the tire outer shoulder must be used.

Total toe

*BE40.20-N-1001-07TST

Model 907 except code A50, CB1, CB4, CB8, R9A, XL4, ZG1, ZG3Toe per wheel

*BE40.20-N-1002-07TST

Model 907 with code CB1 except code A50, CB4, CB8, R9A, XL4, ZG1, ZG3, model 907 with code CB4 except code A50, CB1, CB8, R9A, XL4, ZG1, ZG3, model 907 with code CB8 except code A50, CB1, CB4, R9A, XL4, ZG1, ZG3Toe per wheel

*BE40.20-N-1003-07TST

Model 907 with code A50 except code R9A, XL4, ZG1, ZG3Toe per wheel

*BE40.20-N-1004-07TST

Model 907 with code XL4 except code R9A, ZG1, ZG3Toe per wheel

*BE40.20-N-1005-07TST

Model 907 with code R9A except code A50, XL4, ZG1, ZG3Toe per wheel

*BE40.20-N-1007-07TST

Model 907 with code A50, R9A except code XL4, ZG1, ZG3Toe per wheel

*BE40.20-N-1008-07TST

Model 907 with code ZG1, model 907 with code ZG3Toe per wheel

*BE40.20-N-1009-07TST

Adjust

7

Adjust toe to determined specified value.

If the actual values deviate from the specified values or if the tire outer shoulder exhibits wear.

Note on calculation of tightening torque when using insertion or socket tools with various effective lengths

AH00.00-P-0015-01CW

 To do so, release counternuts (3), adjust toe by turning tie rods (4) then tighten counternuts (3) again. Counterhold the ball heads (1) while doing so.

 Counternut, tie rod to ball head

*BA46.40-N-1001-06TS

8

Check bellows of tie rods (4) for twisting.

If corresponding findings are present,



Correct the position of affected boots.

9

Remove holding device (055) and tensioning nut.

 Retainer device

*129589012100

 Tensioning nut

*906589002100

10

Remove wheel spreader (030).



Check

11

Perform final measurement.

AR40.20-D-0200TS

Front axle toe

Number

Designation

Model 907 with code IT5 except code A50, CB1, CB4, CB8, R9A, XL4, ZG1, ZG3

Model 907 with code CB1, IT5 except code A50, CB4, CB8, R9A, XL4, ZG1, ZG3,
model 907 with code CB4, IT5 except code A50, CB1, CB8, R9A, XL4, ZG1, ZG3,
model 907 with code CB8, IT5 except code A50, CB1, CB4, R9A, XL4, ZG1, ZG3

BE40.20-N-1001-07TST

Total toe

Permissible difference in front axle toe between right and left sides of vehicle

°

0° 05'

0° 05'

Maximum tolerance

°

0° 10'

0° 10'

Front axle toe

Number

Designation

Model 907 with code A50, IT5 except code R9A, XL4, ZG1, ZG3

Model 907 with code IT5, XL4 except code R9A, ZG1, ZG3

BE40.20-N-1001-07TST

Total toe

Permissible difference in front axle toe between right and left sides of vehicle

°

0° 05'

0° 05'

Maximum tolerance

°

0° 10'

0° 10'

Front axle toe

Number

Designation

Model 907 with code IT5, R9A except code A50, ZG1, ZG3

Model 907 with code A50, IT5, R9A except code XL4, ZG1, ZG3

BE40.20-N-1001-07TST

Total toe

Permissible difference in front axle toe between right and left sides of vehicle

°

0° 05'

0° 05'

Maximum tolerance

°

0° 10'

0° 10'

Front axle toe

Number

Designation

Model 907 with code IT5, ZG1,
model 907 with code IT5, ZG3

BE40.20-N-1001-07TST

Total toe

Permissible difference in front axle toe between right and left sides of vehicle

°

0° 05'

Maximum tolerance

°

0° 10'

Front axle toe

Number

Designation

Model 907 with code IT5 except code A50, CB1, CB4, CB8, R9A, XL4, ZG1, ZG3

BE40.20-N-1002-07TST

Toe per wheel

Transverse control arm angle 5.13° / front axle load 1850 kg

Specified value (actual values outside tolerance)

°

-0° 04' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 04' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 09'

Transverse control arm angle 6.18° / front axle load 1770 kg

Specified value (actual values outside tolerance)

°

-0° 01' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 01' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 06'

Transverse control arm angle 7.22° / front axle load 1690 kg

Specified value (actual values outside tolerance)

°

0° 02' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 02' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 03'

Transverse control arm angle 8.26° / front axle load 1610 kg

Specified value (actual values outside tolerance)

°

0° 04' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 04' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 01'

Transverse control arm angle 9.29° / front axle load 1530 kg

Specified value (actual values outside tolerance)

°

0° 06' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 06' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 01'

Transverse control arm angle 10.30° / front axle load 1450 kg

Specified value (actual values outside tolerance)

°

0° 08' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 08' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 03'

Transverse control arm angle 11.31° / front axle load 1370 kg

Specified value (actual values outside tolerance)

°

0° 10' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 10' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 05'

Transverse control arm angle 12.32° / front axle load 1290 kg

Specified value (actual values outside tolerance)

°

0° 12' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 12' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 07'

Transverse control arm angle 13.31° / front axle load 1210 kg

Specified value (actual values outside tolerance)

°

0° 13' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 13' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 08'

Transverse control arm angle 14.30° / front axle load 1130 kg

Specified value (actual values outside tolerance)

°

0° 15' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 15' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 10'

Front axle toe

Number

Designation

Model 907 with code CB1, IT5 except code A50, CB4, CB8, R9A, XL4, ZG1, ZG3,
model 907 with code CB4, IT5 except code A50, CB1, CB8, R9A, XL4, ZG1, ZG3,
model 907 with code CB8, IT5 except code A50, CB1, CB4, R9A, XL4, ZG1, ZG3

BE40.20-N-1003-07TST

Toe per wheel

Transverse control arm angle 7.40° / front axle load 1850 kg

Specified value (actual values outside tolerance)

°

-0° 04' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 04' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 09'

Transverse control arm angle 8.36° / front axle load 1770 kg

Specified value (actual values outside tolerance)

°

-0° 02' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 02' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 07'

Transverse control arm angle 9.31° / front axle load 1690 kg

Specified value (actual values outside tolerance)

°

0° 00' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 00' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 05'

Transverse control arm angle 10.26° / front axle load 1610 kg

Specified value (actual values outside tolerance)

°

0° 02' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 02' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 03'

Transverse control arm angle 11.20° / front axle load 1530 kg

Specified value (actual values outside tolerance)

°

0° 04' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 04' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 01'

Transverse control arm angle 12.14° / front axle load 1450 kg

Specified value (actual values outside tolerance)

°

0° 05' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 05' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 00'

Transverse control arm angle 13.07° / front axle load 1370 kg

Specified value (actual values outside tolerance)

°

0° 07' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 07' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 02'

Transverse control arm angle 13.99° / front axle load 1290 kg

Specified value (actual values outside tolerance)

°

0° 08' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 08' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 03'

Transverse control arm angle 14.91° / front axle load 1210 kg

Specified value (actual values outside tolerance)

°

0° 09' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 09' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 04'

Transverse control arm angle 15.81° / front axle load 1130 kg

Specified value (actual values outside tolerance)

°

0° 10' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 10' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 05'

Front axle toe

Number

Designation

Model 907 with code A50, IT5 except code R9A, XL4, ZG1, ZG3

BE40.20-N-1004-07TST

Toe per wheel

Transverse control arm angle 5.48° / front axle load 2000 kg

Specified value (actual values outside tolerance)

°

-0° 03' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 03' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 08'

Transverse control arm angle 6.58° / front axle load 1910 kg

Specified value (actual values outside tolerance)

°

0° 00' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 00' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 05'

Transverse control arm angle 7.66° / front axle load 1820 kg

Specified value (actual values outside tolerance)

°

0° 03' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 03' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 02'

Transverse control arm angle 8.74° / front axle load 1730 kg

Specified value (actual values outside tolerance)

°

0° 05' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 05' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 00'

Transverse control arm angle 9.81° / front axle load 1640 kg

Specified value (actual values outside tolerance)

°

0° 07' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 07' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 02'

Transverse control arm angle 10.87° / front axle load 1550 kg

Specified value (actual values outside tolerance)

°

0° 09' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 09' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 04'

Transverse control arm angle 11.92° / front axle load 1460 kg

Specified value (actual values outside tolerance)

°

0° 11' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 11' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 06'

Transverse control arm angle 12.96° / front axle load 1370 kg

Specified value (actual values outside tolerance)

°

0° 13' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 13' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 08'

Transverse control arm angle 14.00° / front axle load 1280 kg

Specified value (actual values outside tolerance)

°

0° 14' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 14' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 09'

Transverse control arm angle 15.03° / front axle load 1190 kg

Specified value (actual values outside tolerance)

°

0° 15' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 15' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 10'

Front axle toe

Number

Designation

Model 907 with code IT5, XL4 except code R9A, ZG1, ZG3

BE40.20-N-1005-07TST

Toe per wheel

Transverse control arm angle 4.25° / front axle load 2100 kg

Specified value (actual values outside tolerance)

°

-0° 04' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 04' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 09'

Transverse control arm angle 5.48° / front axle load 2000 kg

Specified value (actual values outside tolerance)

°

-0° 01' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 01' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 06'

Transverse control arm angle 6.69° / front axle load 1900 kg

Specified value (actual values outside tolerance)

°

0° 02' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 02' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 03'

Transverse control arm angle 7.90° / front axle load 1800 kg

Specified value (actual values outside tolerance)

°

0° 05' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 05' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 00'

Transverse control arm angle 9.09° / front axle load 1700 kg

Specified value (actual values outside tolerance)

°

0° 08' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 08' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 03'

Transverse control arm angle 10.28° / front axle load 1600 kg

Specified value (actual values outside tolerance)

°

0° 10' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 10' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 05'

Transverse control arm angle 11.45° / front axle load 1500 kg

Specified value (actual values outside tolerance)

°

0° 12' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 12' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 07'

Transverse control arm angle 12.62° / front axle load 1400 kg

Specified value (actual values outside tolerance)

°

0° 14' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 14' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 09'

Transverse control arm angle 13.77° / front axle load 1300 kg

Specified value (actual values outside tolerance)

°

0° 16' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 16' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 11'

Transverse control arm angle 14.91° / front axle load 1200 kg

Specified value (actual values outside tolerance)

°

0° 17' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 17' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 12'

Front axle toe

Number

Designation

Model 907 with code IT5, R9A except code A50, ZG1, ZG3

BE40.20-N-1007-07TST

Toe per wheel

Transverse control arm angle 7.28° / front axle load 1850 kg

Specified value (actual values outside tolerance)

°

-0° 13' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 13' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 18'

Transverse control arm angle 8.23° / front axle load 1770 kg

Specified value (actual values outside tolerance)

°

-0° 11' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 11' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 16'

Transverse control arm angle 9.18° / front axle load 1690 kg

Specified value (actual values outside tolerance)

°

-0° 09' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 09' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 14'

Transverse control arm angle 10.12° / front axle load 1610 kg

Specified value (actual values outside tolerance)

°

-0° 07' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 07' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 12'

Transverse control arm angle 11.06° / front axle load 1530 kg

Specified value (actual values outside tolerance)

°

-0° 05' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 05' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 10'

Transverse control arm angle 11.99° / front axle load 1450 kg

Specified value (actual values outside tolerance)

°

-0° 03' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 03' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 08'

Transverse control arm angle 12.91° / front axle load 1370 kg

Specified value (actual values outside tolerance)

°

-0° 02' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 02' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 07'

Transverse control arm angle 13.82° / front axle load 1290 kg

Specified value (actual values outside tolerance)

°

-0° 01' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 01' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 06'

Transverse control arm angle 14.73° / front axle load 1210 kg

Specified value (actual values outside tolerance)

°

0° 00' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 00' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 05'

Transverse control arm angle 15.63° / front axle load 1130 kg

Specified value (actual values outside tolerance)

°

0° 01' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 01' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 04'

Front axle toe

Number

Designation

Model 907 with code A50, IT5, R9A except code XL4, ZG1, ZG3

BE40.20-N-1008-07TST

Toe per wheel

Transverse control arm angle 5.42° / front axle load 2000 kg

Specified value (actual values outside tolerance)

°

-0° 09' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 09' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 14'

Transverse control arm angle 6.51° / front axle load 1910 kg

Specified value (actual values outside tolerance)

°

-0° 06' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 06' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 11'

Transverse control arm angle 7.59° / front axle load 1820 kg

Specified value (actual values outside tolerance)

°

-0° 03' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 03' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 08'

Transverse control arm angle 8.66° / front axle load 1730 kg

Specified value (actual values outside tolerance)

°

-0° 01' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 01' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 06'

Transverse control arm angle 9.72° / front axle load 1640 kg

Specified value (actual values outside tolerance)

°

0° 02' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 02' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 03'

Transverse control arm angle 10.78° / front axle load 1550 kg

Specified value (actual values outside tolerance)

°

0° 04' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 04' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 01'

Transverse control arm angle 11.82° / front axle load 1460 kg

Specified value (actual values outside tolerance)

°

0° 06' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 06' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 01'

Transverse control arm angle 12.86° / front axle load 1370 kg

Specified value (actual values outside tolerance)

°

0° 07' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 07' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 02'

Transverse control arm angle 13.88° / front axle load 1280 kg

Specified value (actual values outside tolerance)

°

0° 09' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 09' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 04'

Transverse control arm angle 14.90° / front axle load 1190 kg

Specified value (actual values outside tolerance)

°

0° 10' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 10' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 05'

Front axle toe

Number

Designation

Model 907 with code IT5, ZG1,
model 907 with code IT5, ZG3

BE40.20-N-1009-07TST

Toe per wheel

Transverse control arm angle 2.75° / front axle load 2000 kg

Specified value (actual values outside tolerance)

°

-0° 04' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 04' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 09'

Transverse control arm angle 3.96° / front axle load 1910 kg

Specified value (actual values outside tolerance)

°

-0° 01' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

-0° 01' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 06'

Transverse control arm angle 5.16° / front axle load 1820 kg

Specified value (actual values outside tolerance)

°

0° 01' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 01' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 04'

Transverse control arm angle 6.35° / front axle load 1730 kg

Specified value (actual values outside tolerance)

°

0° 03' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 03' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

-0° 02'

Transverse control arm angle 7.53° / front axle load 1640 kg

Specified value (actual values outside tolerance)

°

0° 05' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 05' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 00'

Transverse control arm angle 8.70° / front axle load 1550 kg

Specified value (actual values outside tolerance)

°

0° 07' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 07' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 02'

Transverse control arm angle 9.87° / front axle load 1460 kg

Specified value (actual values outside tolerance)

°

0° 08' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 08' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 03'

Transverse control arm angle 11.02° / front axle load 1370 kg

Specified value (actual values outside tolerance)

°

0° 09' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 09' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 04'

Transverse control arm angle 12.17° / front axle load 1280 kg

Specified value (actual values outside tolerance)

°

0° 10' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 10' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 05'

Transverse control arm angle 13.31° / front axle load 1190 kg

Specified value (actual values outside tolerance)

°

0° 10' ( 05')

Specified value (actual values within tolerance, wear to outer shoulder of tire)

°

0° 10' ( 05')

Specified value (actual values within tolerance, severe wear to outer shoulder of tire)

°

0° 05'

 Steering linkage

Number

Designation

Model 907, 910

BA46.40-N-1001-06TS

Counternut, tie rod to ball head

Nm

65