Remove/install front and rear rubber bushings in rear axle mount

AR35.10-P-0040C

Remove/install front and rear rubber bushings in rear axle mount

31.8.11

Fig. item etc.

Work instructions

 Removal

When lowering the right side make sure that the fuel hose is not put under too much tension

 Installation

Replace self-locking nuts and bolts

Danger!

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer.

AS00.00-Z-0010-01A



Assembly attachment

*140589016200

1a

Remove/install front rubber mount in rear axle mount

AR35.10-P-0040-02D

 Extraction and insertion tool

*201589104300

Lubricant paste

*BR00.45-Z-1002-06A

1b

Remove/install rear rubber mount in rear axle mount

AR35.10-P-0040-03E

 Extraction and insertion tool

*201589114300

Lubricant paste

*BR00.45-Z-1002-06A

1c

Front bolt, rear axle mount

 Installation: Recut thread on frame floor with tap.



*BA35.10-P-1001-01A

1d

Rear bolt, rear axle mount

 Installation: Recut thread on frame floor with tap.



*BA35.10-P-1002-01A

36

Detach both frame cross struts



*BA61.10-P-1001-01A

105

Remove/install exhaust system complete

Engine 104

AR49.10-P-7000D

Engine 112, 113

AR49.10-P-7000AB

Engine 119

AR49.10-P-7000E

Engine 120

AR49.10-P-7000F

105c

Exhaust shielding plate

106

Rear propeller shaft

 Flexible disk remains on propeller shaft.

Release fitting sleeves on flex disks

AR41.10-P-0050-09DA



Drift for releasing the fitting sleeves in the flexible couplings

Models 129, 140, 170, 202, 203, 210, 215, 220

WF58.50-P-4110-01A



*BA41.10-P-1002-01A

106 A

Propeller shaft intermediate bearing

 Installation: Only tighten the bolts of the propeller shaft intermediate bearing after attaching the flexible coupling to the rear axle differential.



*BA41.40-P-1001-01A

106c

Drive shaft self-locking nut

 Model Series 129.058/063 up to 06/95 and Model Series 129.066 up to 06/92

*126589000100



*BA41.10-P-1003-01A



Clamp connection of propeller shaft

Model 129.058/063/066: changed to slide connection

BT41.10-P-9110-01DA

108

Tunnel end plate



*BA61.10-P-1002-01A

120

Remove/install bracket for ADS level controller

Vehicles with ADS up to 08/95

AR35.10-P-0010-01A

Remove and install link rod of level sensor

Vehicles with ADS manufactured from 09/95 onward

Number

Designation

Model 129

BA35.10-P-1001-01A

Self-locking bolt, front rear axle carrier rubber mount to frame floor

–

Nm

70

with bolt Flange Ø 24 mm

Stage 1

Nm

-

Stage 2

°

-

with bolt flange Ø 26 mm

Stage 1

Nm

-

Stage 2

°

-

BA35.10-P-1002-01A

Self-locking bolt, rear axle carrier rear rubber mount to frame floor

–

Nm

70

with bolt Flange Ø 24 mm

Stage 1

Nm

-

Stage 2

°

-

with bolt flange Ø 26 mm

Stage 1

Nm

-

Stage 2

°

-

Number

Designation

Model
129

BA41.10-P-1002-01A

Self-locking nut, flexible coupling to rear propeller shaft or rear axle differential.

M10

Nm

40

M12

Nm

60

BA41.10-P-1003-01A

Clamping nut of propellor shaft

Nm

40

Number

Designation

Model 129

BA41.40-P-1001-01A

Bolt, propeller shaft intermediate bearing to frame floor assembly

Self-tapping screw

Nm

-

Bolt with washer

Nm

25

Bolt with collar and self-centering tip

Nm

30

Bolt with collar and without self-centering tip

Nm

-

Number

Designation

Model 129

BA61.10-P-1001-01A

Self-locking bolt connecting rear cross strut to frame floor

Nm

120

BA61.10-P-1002-01A

Self-safety bolt of tunnel end panel to frame floor

Nm

25

Number

Designation

Order number

BR00.45-Z-1002-06A

Lubricating paste, rubber parts 2.5 kg, DB supply specification 6867.00

A 000 989 01 60