Retrofit daytime running lights headlamp

AN82.10-P-0100MCD

Retrofit daytime running lights headlamp

6.12.11



Removing



Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

1

Disconnect battery ground line

AR54.10-P-0003MCC

2

Remove CBS front end (2)

AR88.00-P-1010MCC

3

Remove left front lamp unit (E1)

* not for USA

AR82.10-P-4730MCC

* for USA only

AR82.10-P-4730MCU

4

Adjust the left front seat to the rear

5

Unclip left tweeter from instrument panel and place to one side with electrical line connected

On vehicles up to 30.8.10 with code (C17) Sound package (2 tweeters, 2 bass reflex boxes and diplexer) (FFO) or

On vehicles with code (C54) Sound system 2

AR82.62-P-1000MCC

6

Unclip SAM control unit (N10/10) in front area (arrow A) and fold down to the rear

7

Remove screws/bolts (11) and carefully lower SAM control unit (N10/10) until electrical connectors are accessible



Install

 Danger!

Risk of injury caused by burns to skin and eyes. Risk of poisoning caused by inhaling fumes when working with heat-shrinkable tubing.

Work in well ventilated rooms only. Wear safety glasses with side protection and protective gloves.

AS00.19-Z-0001-01A

8

Retrofit electrical wiring harness (3) for daytime running lights headlamp (1)

On vehicles without code (460) Canada version

AN82.10-P-0100-01MCC

 Wiring harness repair kit, basic

*000589139900

 Expanding pliers

*450589123700

 Puller aid

*450589256300

Hot air blower
gotis://E_15/54_12.0

On vehicles with code (460) Canada version

AN82.10-P-0100-01MCD

 Wiring harness repair kit, basic

*000589139900

 Expanding pliers

*450589123700

 Puller aid

*450589256300

9

Tighten SAM control unit (N10/10) with screws/bolts (11)

10

Clip SAM control unit (N10/10) into front area (arrow A)

11

Clip left tweeter into instrument panel

On vehicles up to 30.8.10 with code (C17) Sound package (2 tweeters, 2 bass reflex boxes and diplexer) (FFO) or

On vehicles with code (C54) Sound system 2

AR82.62-P-1000MCC

12

Retrofit daytime running lights control units (5)

AN82.10-P-0100-02MCD

13

Install left front lamp unit (E1)

AR82.10-P-4730MCC

14

Install CBS front end (2)

AR88.00-P-1010MCC

15

Retrofit daytime running lights headlamp (1) into CBS front end (2)

AN82.10-P-0100-04MCD

16

Connect ground cable to battery

AR54.10-P-0003MCC

17

Enter special equipment in online vehicle data card via vehicle documentation system (VeDoc)

On vehicles with code (460) Canada version

 Delete:

 Code (K06) Daytime running lights

18

Connect Star Diagnosis and select vehicle via the vehicle identification number (VIN)

On vehicles with code (460) Canada version

19

Run variant coding with XENTRY using software calibration number (SCN)

On vehicles with code (460) Canada version

 Variant coding with XENTRY using the software calibration number (SCN) must be carried out for the following control unit:

"SAM control unit"

20

Disconnect Star Diagnosis

On vehicles with code (460) Canada version

21

Deactivate daytime running lights circuit on vehicle

On vehicles with code (K06) Daytime running lights and without code (460) Canada version

 Switch off ignition and remove key. Operate headlamp flasher and press "Release" button on key at same time.

A signal tone is emitted to confirm that the daytime running lights are switched off.

Part no.

Designation

Quantity

DG 98 (see EPC)

Daytime running lights LED parts kit

1