P83.25-0287-06
19 Airbag connector
20 Transverse pipe
22 Hex. nut M6
23 Hex. head screw M8
25 Wiring duct
26 Screw
30 Holder, transverse pipe
31 Screw
35 Cockpit separation point
P83.25-0285-06
22 Hex. nut M6
27 Cable straps
28 Shift lock cables
29 Heater core temperature sensor connector (B10/1)
32 Holder, jacket tube separation point
33 Brace
| Removal, installation | ||
Danger! | Risk of injury to skin and eyes from scalding with hot coolant which splashes out. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage bottles. Wear protective gloves, protective clothing and eye protection. | |
1 | Drain coolant | Engine 111 | |
Engine 112, 113 | |||
Engine 604, 605, 606 | |||
Engine 119 | |||
Engine 120 | |||
Installation: Pour in coolant. | |||
2 | Remove left air inlet | ||
3 | Remove right air inlet | ||
4 | Remove water collector | ||
5 | Pull off heater feed and return hoses, loosen 3 hose clamps | Plug openings (parts kit). | |
6 | Remove instrument panel | Installation: Before installing the instrument panel, check for proper functioning. | |
N | Remove center console | ||
8 | Remove air ducts in rear compartment /stowage compartment ventilation | ||
9 | Take out left floor covering | ||
10 | Remove floor covering on right | ||
11 | Remove left/right rear compartment air ducts | ||
12 | Pull off ignition/starter switch connector (S2/1) | ||
13 | Remove jacket tube | ||
14 | Remove connector (19) from passenger airbag | ||
15 | Disconnect vacuum lines at cockpit separation point (35) | ||
16 | Separate blower motor connector | ||
17 | Pull off coupling, vacuum valve (Y13) | ||
18 | Pull off temperature sensor connector (29) heat exchanger (B10/1) | ||
19 | Remove holder for jacket tube separation point (32) on brace (33) | ||
20 | Open cable straps (27) | ||
21 | Unclip shift lock cables (28) and detach from steering lock and pedal system | Vehicles with automatic transmission Code 420/425. | |
22 | Remove holder (30), unscrew screw (31) | ||
23 | Remove transverse pipe (20). For this purpose, unscrew screws (23) and nuts (22) | ||
24 | Remove air ducts for air nozzles on left and right | ||
25 | Loosen wiring duct (25), unscrew screws (26) and lay down to side | ||
26 | Remove heater housing | ||
27 | Install in opposite order |
참조 문서
- ar2000p1142ha 냉각수 배출, 주입
- ar2000p1142ha
- ar2000p1142hg 냉각수 배출, 주입
- ar2000p1142hw
- ar4610p0400b
- ar6810p1000f 계기반의 탈, 장착
- ar6810p1000f
- ar6820p2000f
- ar6820p2050f
- ar6820p2070f
- ar8325p1402f
- ar8325p1403f
- ar8325p1404f
- as2000z000101a 뜨거운 냉각수 분출 시 입은 화상에 의한 피부와 안구의 상해 위험 냉각수의 음용으로 인한 중독 위험
- ra20001190100x
- ra20001200100x