ar4110t0050b

Remove/install propeller shaft

유형 ar · 주제 41.10 · 버전 0205 · 2009-11-19

적용 대상: MODEL 613.355 /358 /388 /364 /365 /455 /485

“ko”(으)로는 제공되지 않아 영어(으)로 표시합니다.

위치

기능 그룹 2 섀시 › 41 추진축 › 41.10 추진축 — 시리즈 613 (모델 355, 358, 364, 365, 388, 455, 485)

EinPAS 17 드라이브 트레인/액슬 › 17.40 드라이브 샤프트 › 17.40.30 드라이브 샤프트/사륜구동 — 시리즈 613 (모델 355, 358, 364, 365, 388, 455, 485)

AR41.10-T-0050B

Remove/install propeller shaft

17.11.09

MODEL 613.355 /358 /388 /364 /365 /455 /485

Remove/install propeller shaft

T41.10-0010-11

Shown on model 613.4

1 Propeller shaft

2 Retarder

3 Rear axle

4 Sliding sleeve

Modification notes

31.5.01

Step revised.

Step 3: References for 613.355/ 358/ 388/ 455/ 485 and 613.364/ 365 added.

Remove/install

Danger!

Risk of injury caused by touching hot retarder and by scalding from hot retarder oil. Risk of injury to skin or eyes caused by retarder oil escaping under high pressure

Do not carry out any work unless retarder is switched off. Wear suitable protective clothing and safety glasses when working on the hot retarder.

AS43.30-Z-0001-01A

Installation

Replace self-locking nuts

1

Secure vehicle against rolling

2

Raise vehicle

So that the propeller shaft can be turned for removal.

AR00.60-T-1000B

3

Detach lower engine compartment paneling

Model 613.355/ 358/ 388/ 455/ 485

Only perform the steps necessary for removing the paneling under the transmission.

AR61.20-T-1105B

Model 613.364/ 365

AR61.20-T-1105C

Danger!

Risk of injury caused by moving parts that can pinch, crush or, in extreme cases, even sever extremities

No parts of the body or limbs should be within the operating range of the mechanism when moving components.

AS00.00-Z-0009-01A

4

Detach propeller shaft (1) from retarder (2) and from rear axle (3)

Before detaching the propeller shaft:

- Identify sliding sleeve (4) relative to propeller shaft (1),

- and bind the propeller shaft together via both joints by means of a suitable cable.

Installation: If the propeller shaft has been separated, ensure that the markings are aligned when pushing the propeller shaft and sliding sleeve together.

*BA41.10-N-1002-01E

*BA41.10-N-1003-01E

*BA41.10-N-1004-01E

5

Install in the reverse order

Propeller shaft

Number

Designation

Model 613.355/455/485

Model 613.358/
388

Model 613.364/
365

BA41.10-N-1001-01E

Nut, propeller shaft flange to rear axle (without spring washers)

Nm

110

-

-

BA41.10-N-1002-01E

bolt, propeller shaft to rear axle

Nm

110

110

110

BA41.10-N-1003-01E

Bolt, propeller shaft to transmission output flange

Nm

110

110

110

BA41.10-N-1004-01E

Bolt, propeller shaft to retarder output flange

Nm

105

105

105

참조 문서