ar2210d1135te

Remove/install engine stabilizer mount

유형 ar · 주제 22.10 · 버전 0201 · 2019-12-09

적용 대상: Engine 780.703 in model 910

“ko”(으)로는 제공되지 않아 영어(으)로 표시합니다.

위치

기능 그룹 1 엔진 › 22 어셈블리 서스펜션 › 22.10 어셈블리 마운트, 어셈블리 캐리어 — 시리즈 910

EinPAS 15 엔진 › 15.15 연소 엔진 전체/엔진 블럭/크랭크 어셈블리 › 15.15.20 엔진 서스펜션 — 시리즈 910

엔진/변속기에도 적용: 780 703

AR22.10-D-1135TE

Remove/install engine stabilizer mount

22.11.2019

Engine

780.703 in model 910

Modification notes

08.07.2019

Bolt, engine stabilizer mount at bottom to integral carrier

BA22.10-N-1001-01TE

08.07.2019

Screw, engine stabilizer mount at bottom to holder

BA22.10-N-1002-01TE

Remove/install engine stabilizer mount

1

Engine stabilizer mount

2

Bolts

3

Screw

4

Frame-type integral support

D22.10-A008-76

Danger

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

Danger

Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)

Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.

AS00.00-Z-0035-01A

Topical note

General information on handling vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system

AH00.00-Z-0300-01A

Remove/install

1

Remove lower engine compartment paneling.

AR61.20-D-1105TS

2

Support axle drive module in the hatched area with the major assembly mount.

000 588 11 62 00 Major assembly mount

WS01.00-P-0092B


The axle drive module must remain in the installation position and may not tilt.
Otherwise, damage may occur on the threads when unscrewing and screwing in the screws (2, 3).

3

Remove screws (2, 3).

Topical note

Notes on threaded connections fastened using a tightening angle-based tightening process

AH00.00-P-0020-01A

Topical note

Notes on self-locking nuts and bolts

AH00.00-N-0001-01A

Bolt, engine stabilizer mount at bottom to integral carrier

*BA22.10-N-1001-01TE

Screw, engine stabilizer mount at bottom to holder

*BA22.10-N-1002-01TE

4

Remove engine stabilizer mount (1).

To do this, swivel engine stabilizer mount (1) out of the integral carrier (4).

5

Install in the reverse order.

Engine mounts, engine supports

Number

Designation

Engine 780.703 in model 910

BA22.10-N-1001-01TE

Bolt, engine stabilizer mount at bottom to integral carrier

Stage 1

Nm

60

Stage 2

°

120

Engine mounts, engine supports

Number

Designation

Engine 780.703 in model 910

BA22.10-N-1002-01TE

Screw, engine stabilizer mount at bottom to holder

Stage 1

Nm

60

Stage 2

°

120

참조 문서