P68.30-3337-06
Shown on right side of vehicle
1 Seat belt guide
2 Seat belt
3 Cover (only on right side of vehicle)
4 Screw
5 Bracket (only on right side of vehicle)
6 Edge guard
B48/3x1 Belt tensioning sensor connector (only on right side of vehicle)
P68.30-3548-04
Driver side, as of 31.8.10
2 Seat belt
15 Lock
16 Support
17 Belt end fitting tensioner
P68.30-3338-09
Shown on right side of vehicle
2 Seat belt
7 B-pillar paneling
8 Screw
12 Guide
13 Screw
14 Insulating material
9 Edge guard
10 Side roof frame paneling
11 Screw
| Remove/install | ||
Danger! | Risk of injury caused by backrest suddenly folding forward if release lever is accidentally operated during inspection and repair work | When working on the seat, be careful not to accidentally release the backrest mechanism allowing the seat to fold forward. Keep body parts clear of the backrest travel area. | |
1 | Move left and right seat to front-most position and fold toward front | ||
2 | Unhook seat belt (2) from belt guide (1) on seat | ||
3 | Unclip and remove cover (3) | When removing paneling from B-pillar (7) on front passenger side. | |
4 | Detach wiring harness from bracket (5) and disconnect belt tensioning sensor connector (B48/3x1) | When removing paneling from B-pillar (7) on front passenger side. | |
Observe installation position (arrow A) of wiring harness. | |||
5 | Remove bolt (4) from lower belt end fitting of seat belt (2) | When removing paneling from B-pillar (7) on front passenger side. Up to 30.8.10, when removing B-pillar paneling (7) on driver side. | |
| |||
6 | Turn lock (arrow) in lock (15) of seat belt (2) 90° clockwise and remove seat belt (2) from belt end fitting tensioner (17) | As of 31.8.10, when removing B-pillar paneling (7) on driver side. | |
Installation: Ensure that lock (15) is seated correctly in mount (16) and observe installation position of seat belt (2). | |||
7 | Loosen edge guard (6) in area of side roof frame paneling (10) | ||
8 | Loosen edge guard (6) in area of B-pillar paneling (7) | ||
9 | Remove left or right side paneling in trunk | ||
10 | Remove rear roof frame trim | ||
11 | Unscrew bolt (11) from side roof frame paneling (10) | ||
12 | Unclip side roof frame paneling (10) in rear area | On vehicles without code (I52) Head airbag | |
Installation: Position edge guard (9) above side roof frame paneling (10). | |||
13 | Detach side roof frame paneling (10) from guides (12) in marked areas (arrows B). | On vehicles without code (I52) Head airbag | |
14 | Carefully push side roof frame paneling (10) to side until bolts (8) are accessible. | On vehicles without code (I52) Head airbag | |
15 | Remove side roof frame paneling (10) | On vehicles with code (I52) Head airbag | |
16 | Unscrew bolts (8, 13) from B-pillar paneling (7) | ||
17 | Remove B-pillar paneling (7) and guide seat belt (2) through opening into B-pillar paneling (7) | Installation: Position edge guard (9) above B-pillar paneling (7). | |
18 | Remove damping material (14) from B-pillar paneling (7) | When replacing B-pillar paneling (7). | |
19 | Install in the reverse order |
Seat belts/emergency tensioning retractors
参照文書
- ar6830p4470mcc リヤ·ルーフ·フレーム·ライニングの脱着
- ar6830p4800mcu
- as9100z000501v 点検·修理作業中にリリ一ス·レバ一を不用意に操作し、バックレストが突然前方に倒れて負傷する危険