ar4230p0160gh

Remove/install ABS measuring ring

Vrsta ar · tema 42.30 · verzija 0110 · 2020-02-04

Vrijedi za: Model 461 with rear axle 741.171/52/53 Model 463 (except 463.270/271) with rear axle 748 up to model year 2013

Nije dostupno na jeziku „hr”; prikazano na jeziku Engleski.

Smještaj

Funkcijska skupina 2 Donji postroj › 42 Kočnice - hidraulika i mehanika › 42.30 Anti-blokirajući sistem (ABS) — Serija 461 · Serija 463 (modeli 200, 202, 204, 206, 207, 208, 209, 210, 215, 218, 220, 221, 222, 224, 225, 227, 228, 230, 231, 232, 233, 234, 235, 236, 237, 238, 239, 240, 241, 242, 243, 244, 245, 246, 247, 248, 249, 250, 254, 255, 260, 261, 272, 273, 274, 275, 276, 277, 280, 300, 303, 304, 306, 307, 308, 309, 315, 318, 320, 321, 322, 323, 324, 325, 327, 328, 330, 331, 332, 333, 335, 336, 338, 340, 341, 342, 343, 346, 348, 349, 350)

EinPAS 26 Active safety system › 26.20 Braking/traction control › 26.20.12 Sensor/switch/wiring harness — Serija 461 · Serija 463 (modeli 200, 202, 204, 206, 207, 208, 209, 210, 215, 218, 220, 221, 222, 224, 225, 227, 228, 230, 231, 232, 233, 234, 235, 236, 237, 238, 239, 240, 241, 242, 243, 244, 245, 246, 247, 248, 249, 250, 254, 255, 260, 261, 272, 273, 274, 275, 276, 277, 280, 300, 303, 304, 306, 307, 308, 309, 315, 318, 320, 321, 322, 323, 324, 325, 327, 328, 330, 331, 332, 333, 335, 336, 338, 340, 341, 342, 343, 346, 348, 349, 350)

Vrijedi i za motore/mjenjače: 741 171, 741 52*, 741 53*, 748 ***

AR42.30-P-0160GH

Remove/install ABS measuring ring

03.02.2020

Model

461 with rear axle 741.171/52/53

Model

463 (except 463.270/271) with rear axle 748

up to model year 2013

Remove/install ABS measuring ring

1

Measuring ring for anti-lock braking system (ABS)

2

Drive shaft

P42.30-0321-01

Remove/install

1

Disassemble drive shaft (2) on front axle


Model 461 (except 461.331) with rear axle 741.171/52/53
Model 463 (except 463.270/271) with rear axle 748
up to model year 2013
except code ZQ0 (G 500 4x42)

AR33.30-P-0700A

Model 461.331 with rear axle 741.171/53

AR33.30-P-0700GX

2

Clamp drive shaft (2) into place

3

Grind down ABS measuring ring (1) using straight grinder to 2 mm then separate using chisel (arrow)


Do not damage axle shaft (2).
Otherwise, the ABS measuring ring (1) may not be correctly seated.

4

Press on new ABS measuring ring (1)

Heat up ABS measuring ring (1) to approx. 80 °C then press on using a suitable tool.

5

Install in the reverse order

Povezani dokumenti