Test values for gap dimensions on hoods, doors and lids
Number | Designation | Model | Model | |||
BE60.00-P-1001-01E | Gap dimension | Engine hood to fender | Dimension "A" | mm | 3,5 (1) | 3,5 (1) |
Engine hood to headlamp | Dimension "R" | mm | 4 (–0,5/+1,5) | 4 (–0,5/+1,5) | ||
Engine hood to bumper | Dimension "D" | mm | 4 (0,5) | 4 (0,5) | ||
See picture | – | – | ||||
BE60.00-P-1002-01E | Gap dimension | Front door to A-pillar | Dimension "B" | mm | 6,5 (+1) | 6,5 (+1) |
Front door to fender | Dimension "H" | mm | 3,5 (–0,5/+1) | 3,5 (–0,5/+1) | ||
Front door to rear door | Dimension "I" | mm | 4 (–0,5/+1) | 4 (–0,5/+1) | ||
Front door to roof | Dimension "C" | mm | 6,5 (+1) | 6,5 (+1) | ||
Rear door to C-pillar | Dimension "T" | mm | – | 6 (+1) | ||
Rear door to side piece, bottom | Dimension "J" | mm | 3,5 (+1) | 3,5 (+1) | ||
Front door to rear fender | Dimension "P" | mm | – | – | ||
See picture | – | – | ||||
BE60.00-P-1003-01E | Gap dimension | Trunk lid to rear fender, top | Dimension "F" | mm | 3,5 (1) | – |
Trunk lid to taillamp | Dimension "M" | mm | 4 (1) | – | ||
Rear fender to taillamp | Dimension "U" | mm | – | 2 (0,5) | ||
See picture | – | – | ||||
BE60.00-P-1004-01E | Gap dimension | Rear-end door to roof | Dimension "E" | mm | – | 6,5 (1) |
Rear-end door to rear fender | Dimension "M" | mm | – | 3,5 | ||
Rear-end door to taillamp | Dimension "L" | mm | – | 4 | ||
Rear-end door to bumper | Dimension "S" | mm | – | 5,5 | ||
Rear-end door to D-pillar | Dimension "Q" | mm | – | – | ||
See picture | – | – | ||||
BE60.00-P-1005-01E | Gap dimension | Fuel filler flap | Dimension "K" | mm | 3,5 (0,5) | 3,5 (–0,5/+0,5) |
See picture | – | – | ||||
Feeler gauge
129 589 03 21 00
P60.00-2088-06
Adjust hoods, doors and lids as shown in drawing. The gap should not run wedge-shaped or be too narrow at points. Deviations from parallel gap should be max. 0.5 mm over the entire length. If the inside clearance is too large or too small, the movable body parts must be centered accordingly. The reference measurements apply only for repair work on bodies damaged in accidents.
P60.00-2153-06
Adjust hood, doors and lids as shown in drawings. The gap should not run wedge-shaped or be too narrow at points. Deviations from parallel gap should be max. 0.5 mm over the entire length. If the inside clearance is too large or too small, the movable body parts must be centered accordingly. The reference measurements apply only for repair work on bodies damaged in accidents.
P60.00-2154-06
Adjust hood, doors and lids as shown in drawings. The gap should not run wedge-shaped or be too narrow at points. Deviations from parallel gap should be max. 0.5 mm over the entire length. If the inside clearance is too large or too small, the movable body parts must be centered accordingly. The reference measurements apply only for repair work on bodies damaged in accidents.
P60.00-2333-06
Adjust hood, doors and lids as shown in drawings. The gap should not run wedge-shaped or be too narrow at points. Deviations from parallel gap should be max. 0.5 mm over the entire length. If the inside clearance is too large or too small, the movable body parts must be centered accordingly. The reference measurements apply only for repair work on bodies damaged in accidents.