ar2000p1010ts

Inspect cooling system for leaks

Tyyppi ar · aihe 20.00 · versio 0104 · 2006-07-26

Koskee: ENGINE 272, 273 in MODEL 211, 219

Ei saatavilla kielellä ”fi”; näytetään kielellä Englanti.

Sijainti

Toimintoryhmä 1 Moottori › 20 Moottorin jäähdytys › 20.00 Yleistä — Mallisarja 211 · Mallisarja 219

EinPAS 15 Moottori › 15.25 Moottorin jäähdytysjärjestelmä › 15.25.5 Jäähdytysnestekierto täydellinen — Mallisarja 211 · Mallisarja 219

Koskee myös moottoreita/vaihteistoja: 272 ***, 273 ***

AR20.00-P-1010TS

Inspect cooling system for leaks

12.4.06

ENGINE 272, 273 in MODEL 211, 219

Inspect cooling system for leaks

P20.30-2207-11

1 Cap

2 Coolant expansion reservoir

3 Test cap

4 Pressure pump

Removing

Danger!

Risk of injury to skin and eyes caused by scalding from contact with hot coolant spray. Risk of poisoning from swallowing coolant.

Do not open cooling system unless coolant temperature is below 90°C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers.

Wear protective gloves, protective clothing and safety glasses.

AS20.00-Z-0001-01A

1

Switch on ignition

2

Adjust heater to maximum heat output

3

Unscrew cap (1) on expansion reservoir (2)

Slowly unscrew cap and reduce the excess pressure.

4

Check coolant level and antifreeze content of coolant.

If the antifreeze content of the coolant is too low, either antifreeze must be added or the coolant must be replaced.

Drain coolant, fill.

AR20.00-P-1142TS

5

Screw test cap (3) onto expansion reservoir (2)

*210589009100

6

Connect pressure pump (4) at test cap (3)

*124589242100

7

Apply test pressure to cooling system

To prevent damage to the cooling system, do not exceed the stated test pressure

*BE20.30-P-1005-01A

Checking

8

Inspect condition and installation at hose clamps; retighten or replace if necessary

6 mm socket hexagon on flexible shaft for hose clamps with worm drive

*WH58.30-Z-1001-06A

7 mm socket hexagon on flexible shaft for hose clips with worm drive

*WH58.30-Z-1002-06A

9

Check coolant hoses and heater hoses and their connecting points for condition and coolant loss

Replace coolant hoses and heater hoses if required.

Install

10

Screw test cap (3) onto expansion reservoir (2)

Slowly unscrew the test cap (3) and reduce the excess pressure.

11

Remove pressure pump (4)

12

Screw cap (1) onto expansion reservoir (2)

13

Switch off ignition

Cap for radiator or expansion reservoir

Number

Designation

2-stage
cap

BE20.30-P-1005-01A

Test pressure for pressure-testing cooling system

Excess pressure in bar

1.4

Inspect cooling system for leaks
Inspect cooling system for leaks

124 589 24 21 00

Pressure pump

Test cap

210 589 00 91 00

Commercially available tools

Number

Designation

WH58.30-Z-1001-06A

6 mm socket hexagon on flexible shaft for hose clamps with worm drive

WH58.30-Z-1002-06A

7 mm socket hexagon on flexible shaft for hose clamps with worm drive

Viitatut asiakirjat