Routing diagram |
1 | Vehicle equipment |
2 | DSRC module |
3 | Power supply wiring harness |
4 | Vehicle speed signal line |
5 | Antenna lines |
6 | Wiring harness for DSRC module |
7 | GPS antenna |
A56 | Digital tachograph (DTCO) control unit |
F152 | Vehicle interior fuse and relay module |
W1/4 | HLS cockpit ground point |
D82.88-A001-06
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
| Remove | ||
1 | Determine installation locations. | The installation locations of the various components can vary depending on the equipment installed. | |
2.1 | Remove top center trim on instrument panel. | Model 907, 910 with code FJ6 (Center range with 2 DIN stowage compartments and air vent) | |
| |||
2.2 | Remove top center stowage compartment from instrument panel. | Model 907, 910 with code FJ7 (Center range with stowage compartment) | |
| |||
3.1 | Remove bottom trim for instrument panel on front passenger side. | Model 907, 910 except code FJ4 (Stowage compartment under cockpit) | |
| |||
3.2 | Remove stowage compartment in instrument panel lower part on front passenger side. | Model 907, 910 with code FJ4 (Stowage compartment under cockpit) | |
| |||
4 | Remove lower A-pillar trim on front passenger side. | ||
| Model 907 | ||
| Model 910 | ||
5 | Remove lockable center stowage compartment on instrument panel. | Model 907, 910 with code FJ1 (Folding cover for stowage compartment) | |
| |||
6 | Remove front roof lining. | ||
| |||
7 | Remove stowage tray on instrument panel. | Model 907, 910 with code ES5 (Boost package for instrument panel) | |
| |||
8 | Remove cover for center speaker. | ||
| |||
| Install | ||
Topical note | Notes on retrofitting electrical/optical lines | ||
9 | Mount GPS antenna (7). | See manufacturer's installation instructions. | |
10 | Install DSRC module (2) on windshield. | See manufacturer's installation instructions. | |
11 | Prepare vehicle equipment power supply. | See manufacturer's installation instructions. | |
12 | Retrofit power supply wiring harness (3), vehicle speed signal line (4) and antenna lines (5). | ||
13 | Install vehicle equipment (1). | See manufacturer's installation instructions. | |
14 | Put vehicle equipment (1) into operation. | See manufacturer's instructions. | |
15 | Install remaining parts. | ||
Update Vehicle Documentation (VeDoc) | |||
16 | Attach notes "Toll system retrofitted as per AZ82.88-D-0002TS" and "Vehicle equipment power supply: Fuses F152f# and F152f#" under field organization texts to DG 82. | ||
Update fuse assignment diagram | |||
17 | Add "Toll system" to the assigned fuse slots in the operator's manual "Additional instructions for fuse assignment". |
Referenced documents
- ah5400p000101a Information on preventing damage to electronic components due to electrostatic discharge
- ah8200p000001a Notes on retrofitting electrical/optical lines
- ar6810d0003ts Remove/install stowage tray on instrument panel
- ar6810d1497ts Remove/install upper center trim on instrument panel
- ar6810d1502tsf Remove/install bottom paneling for dashboard on passenger side
- ar6810d1514ts Remove/install upper center stowage compartment on instrument panel
- ar6810d1518ts Remove/install center lockable stowage compartment on instrument panel
- ar6810d1610ts Remove/install stowage compartment in passenger-side instrument panel bottom section
- ar6830d0012tsf Remove/install lower A-pillar trim on front passenger side
- ar6830d0012tsr Remove/install lower A-pillar trim on front passenger side
- ar6830d3446ts Remove/install cover for center speaker
- ar6830d7607ts Remove/install front headliner
- az8288d000003ts Retrofit toll system wiring harness