Remove/install cold reservoir of stationary air conditioner · ar8330w1100a · Mercedes-Benz WIS

AR83.30-W-1100A

Remove/install cold reservoir of stationary air conditioner

3.9.08

MODEL 930, 932, 933, 934 with CODE (H01) Stationary air conditioner, temperature-controlled

MODEL 930, 932, 933, 934 with CODE (H09) Stationary air conditioner

Remove/install cold reservoir of stationary air conditioner

W83.30-1089-12

1 High pressure pipe

2 Retaining plate

3 Sealing

4 Low pressure pipe

5 Cover

W83.30-1090-06

6 Bolts

7 Cold reservoir

8 Cold reservoir electrical connector

9 Condensate line

A61 Stationary air conditioner control unit

Modification notes

30.6.08	"Tightening torque for retaining plate nut with seal at cab rear panel" added.	Step 5	*BA83.30-N-1004-04A
	"Additional oil filling quantity after replacing stationary air conditioner cold reservoir" added	Step 11	*BF83.55-N-1007-01A

 	Remove/install
 Danger!	Risk of explosion caused by welding or soldering work on closed air conditioning system. Risk of poisoning caused by inhaling overheated refrigerant vapors. Risk of injury to skin and eyes caused by contact with liquid refrigerant.	Never perform welding work on or near a closed air conditioning system. No smoking or open flames. Wear safety glasses and protective gloves. Work only in well ventilated areas. Carry out repair work on the air conditioning system circuit only after the system has been discharged.	AS83.00-Z-0001-01A
	Notes on handling R134a refrigerant	Air conditioning with refrigerant R134a	AH83.30-N-0003-01A
	Protect air conditioning circuit and components from moisture when carrying out repair work		AH83.30-N-0005-01A
1	Open maintenance flap
2	Discharge air conditioning system		AR83.30-W-1760A
3	Detach cover (5) on cab rear panel
4	Detach high-pressure line (1) and low-pressure line (4)	 Counterhold connection fittings when loosening union nuts.
		 Installation: Use new sealing rings.
			*BA83.30-N-1003-04A
5	Remove retaining plate (2) of seal (3)		*BA83.30-N-1004-04A
6	Remove seal (3) at connection fittings of cold reservoir (7)	 Then seal the connections of the high-pressure line (1), the low-pressure line (4) and the connection fitting of the cold reservoir (7) with suitable stop plugs.
7	Remove upper bunk	 If present.
8	Remove upper rear wall paneling in cab
9	Disconnect cold reservoir electrical connector (8) from stationary air conditioner control unit (A61)
10	Remove condensation line (9) from cold reservoir (7) at left and right.
11	Remove bolts (6) and remove cold reservoir (7) from cab	 Do not lower cold reservoir (7) while there are still connection fittings in the cab.
		 Installation: Supplement oil filling quantity of refrigerant circuit when replacing the cold reservoir (7): 
		Additional oil filling quantity after replacing stationary air conditioner cold reservoir (7)	*BF83.55-N-1007-01A
12	Install in the reverse order

 Air conditioning

Number	Designation			Model 930, 932, 933, 934 with body 943.890 with code H01, H09


BA83.30-N-1003-04A	Union nut, refrigerant line to cold reservoir connection fitting	WAF 17	Nm	17
		sz. 22	Nm	30
BA83.30-N-1004-04A	Nut, retaining plate with seal to cab rear wall		Nm	2.5

Refrigerant compressor

Number	Designation			Model 950, 952, 953, 954, 930, 932, 933, 934


BF83.55-N-1007-01A	Additional oil filling quantity after replacing stationary air conditioning system cold reservoir	Compressor oil	cm3	40
		Specifications for Operating Fluids	Sheet	BB00.40-P-0362-00A

Referenced documents

ah8330n000301a Notes on handling refrigerant R134a
ah8330n000501a Protect air conditioning circuit and components from moisture when carrying out repair work
ar8330w1760a Drain, evacuate and recharge air conditioning, check for proper operation and check for leaks
as8300z000101a Risk of explosion caused by welding or soldering work on closed air conditioning system. Risk of poisoning caused by inhaling overheated refrigerant vapors. Risk of injury to skin and eyes caused by contact with liquid refrigerant.