Remove/install heater control cable

AR83.20-D-1400A

Remove/install heater control cable

15.7.99

12.6.01

Repair simplified by cutting a repair cutout in instrument panel

Step 14

AR68.10-D-1000-03A



Remove

1.1

Remove cover of radio installation slot

With code ER0, radio pre-installation.

 Unclip electric leads from cover

1.2

Remove radio

With codes EF5, EF6, EF7, ET0 or ET8, radio.

2.1

Remove stowage compartment below pen holder

Except code J19 or J28, tachograph.

2.2

Remove tachograph

With code J19 or J28, tachograph.

AR54.30-D-0001A

3

Remove cover at instrument panel

AR68.10-D-1550A

4

Remove instrument cluster

AR54.30-D-6015C

5.1

Remove stowage compartment above glove compartment

Except code SA6, front passenger airbag.

AR68.10-D-1515A

5.2

Remove front passenger airbag unit

With code SA6, front passenger's airbag.

 When working on the airbag, disconnect ground cable from the battery.

AR91.60-D-0680B

6.1

Remove cover for air nozzle on passenger side

With code SA6, front passenger's airbag.

AR68.10-D-1090A

7

Remove paneling on A-pillars

 Unclip top paneling and pull out upward

8

Remove loudspeaker

AR82.62-D-7833A

9

Remove cover on center part of instrument panel

AR68.10-D-1190A

10

Screw off the air conditioning control and operating unit

 Heating control cable is unclipped. The other plugs and cables remain connected.

11

Remove top part of instrument panel

AR68.10-D-1020B

12

Cut repair cutout in instrument panel

 Max. depth of cut 3 mm.

AR68.10-D-1000-03A

13

Unclip cable (1) at connector and disconnect from adjustment lever (2)

Adjusting

14

Attach cable (1) to climate control pushbutton control unit

15

Attach cable (1) to adjustment lever (2) for heater control

16

Adjust heater control cable (1)

AR83.20-D-1400-01A



Install

17

Install upper section of instrument panel

 Be aware of the cable routing for the radio: the cables must not lie on top of the air duct, as this may cause them to be damaged.

AR68.10-D-1020B

18

Screw on the air conditioning control and operating unit

19

Install covering on center part of instrument panel

AR68.10-D-1190A

20

Install loudspeaker

AR82.62-D-7833A

21

Install the front pillar panelings

 Unclip top paneling and pull out upward

22.1

Install stowage compartment above the glove compartment

Except code SA6, front passenger airbag.

AR68.10-D-1515A

22.2

Install cover over passenger side air nozzle

With code SA6, front passenger's airbag.

AR68.10-D-1090A

23.2

Install front passenger airbag unit

For version with front passenger airbag,
code SA6.

AR91.60-D-0680B

24

Install instrument cluster

AR54.30-D-6015C

25

Install covering on instrument cluster

AR68.10-D-1550A

26.1

Install stowage compartment below pen holder

Except code J19 or J28, tachograph.

26.2

Install tachograph

With code J19 or J28, tachograph.

AR54.30-D-0001A

27.1

Remove cover of radio installation slot

With code ER0, radio pre-installation.

 Clip electrical lines onto the cover.

27.2

Install radio

With codes EF5, EF6, EF7, ET0 or ET8, radio.

28.1

Reconnect ground cable on battery

With code SA6, front passenger's airbag.

29.1

Set time at instrument cluster

Except code J19 or J28, tachograph.

 Perform only if battery ground cable was disconnected because of the front passenger airbag.

30.1

Set time on timer for auxiliary heater

With code H12, hot water auxiliary heater or H86, timer for auxiliary heater.

31.1

Enter radio code

With codes EF5, EF6, EF7, ET0 or ET8, radio.

 See Operating Instructions