P82.60-7413-09
Shown on MODEL 212.0 except CODE 489 (AIRmatic) and except CODE 488 (Steel/air suspension) |
1 | Cover | 4 | Bracket | 7 | Nuts | ||
2 | Left trunk trim | 5 | Electrical connector | N87/3 | Digital Audio Broadcasting control unit | ||
3 | Nut | 6 | Electrical connection with fiber optic cable |
P82.60-7414-08
Vehicles with CODE 488 (Steel/air suspension) or CODE 489 (AIRMATIC) |
4 | Bracket | 9 | Pneumatic line | 11 | Relay base | ||
8 | Nut | 10 | Pressure reservoir | N87/3 | Digital Audio Broadcasting control unit |
Vehicles with CODE 409 (Left/right front multicontour seats) or CODE 432 (Left and right dynamic multicontour seat) |
3 | Nuts |
4 | Bracket |
7 | Nuts |
12 | Nuts |
13 | Vacuum unit |
N87/3 | Digital Audio Broadcasting control unit |
P82.60-9302-06
Topical note | Notes on avoiding damage to optical fibers during repair work | ||
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
| Remove/install | ||
1 | Connect diagnostic system and perform initial startup of Digital Audio Broadcasting control unit (N87/3) | When replacing the Digital Audio Broadcasting control unit (N87/3). | |
| |||
2.1 | Switch off ignition and remove transmitter key from electronic ignition lock control unit | Model 212.0/1 | |
2.2 | Switch off ignition and remove KEYLESS-GO start/stop button from electronic ignition lock control unit | Model 212.0/1 | |
3.1 | Remove cover (1) from left trunk lining (2) | Model 212.0/1 | |
3.2 | Remove left trunk lining (2). | Model 212.0/1 | |
Model 212.0/1 | |||
Model 218.3 | |||
3.3 | Remove luggage compartment trim on left | Model 218.9 | |
4 | Unscrew nuts (12) and place vacuum unit (13) to one side with lines connected | Model 212.0/1 | |
5 | Unscrew nuts (8) | Model 212.0/1 | |
Nut, pressure reservoir to longitudinal member | |||
6 | Place pressure reservoir (10) to one side with pneumatic line (9) connected | Model 212.0/1 | |
Installation: Observe routing of pneumatic line (9). | |||
7 | Remove relay socket (11) from bracket (4) and place to one side with electrical lines connected | Model 212.0/1 | |
8 | Unscrew nuts (3) | ||
9 | Remove bracket (4) with Digital Audio Broadcasting control unit (N873) and place to one side with electrical lines connected | Installation: Ensure correct installation position of electrical lines. | |
10 | Disconnect electrical connector (5) | ||
11 | Disconnect electrical connection with optical fiber (6) | ||
12 | Cover up connector of electrical connection with optical fiber (6) and equipment connection on Digital Audio Broadcasting control unit (N87/3) | ||
13 | Remove bracket (4) with Digital Audio Broadcasting control unit (N87/3) | ||
14 | Unscrew nuts (7) and remove Digital Audio Broadcasting control unit (N87/3) from bracket (4) | When replacing the Digital Audio Broadcasting control unit (N87/3). | |
15 | Install in the reverse order |
Referenced documents
- ad0000p200004a
- ad0000p200004a Connect STAR DIAGNOSIS and read out fault memory
- ah5400p000101a Information on preventing damage to electronic components due to electrostatic discharge
- ah8260p000105ak Notes on avoiding damage to optical fibers during repair work
- ar6830p1180elx Remove/install load compartment inner side paneling
- ar6830p4600el Remove paneling in trunk
- ar6830p4600ew Remove paneling in trunk