Shown on model 463.248 |
1 | Expansion reservoir |
3 | Nut |
4 | Filler neck |
9 | Screw |
P82.35-2164-06
P82.35-2166-09
Shown on model 463.248 |
2 | Wheel well liner | 7 | Fitting | M5/2 | HCS [SRA] pump | ||
5 | Hose | 8 | Washer fluid reservoir | M5/3 | Rear-end door washer fluid pump | ||
6 | Clip | M5/1 | Windshield washer fluid pump | S42 | Windshield washer fluid level indicator switch |
P82.35-2210-09
Shown on model 463.323 |
5 | Hose | 8 | Washer fluid reservoir | M5/3 | Rear-end door washer fluid pump | ||
6 | Clip | M5/1 | Windshield washer fluid pump | S42 | Windshield washer fluid level indicator switch | ||
7 | Fitting | M5/2 | HCS [SRA] pump |
| Remove/install | ||
Warning | Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. | |
1 | Remove expansion reservoir (1) |
| |
On model 463.322/323, the washer fluid reservoir (8) is on the left side of the vehicle. | |||
2 | Remove wheel well liner (2) | On model | |
463.202/222/236/237/243/244/ | |||
On model 463.322/323, remove on left side. | |||
3 | Remove air plenum chamber and water collector | ||
Only on model 463.202/ 222/ 236/ 237/ 243 | |||
4 | Unscrew nut (3) from filler neck (4) | On model | |
463.202/ 222/ 236/ 237/ 243/ 244/ 245/ 246/ 247/ 248/ 249/ 250/ 254/ 303/ 306/ 309/332/ 333/ 336/340/ 341/ 346 on right side. | |||
On model 463.322/323 on left side. | |||
5 | Pull filler neck (4) from washer fluid reservoir (8) | Installation: When installing the filler neck (4), check that the sealing ring is seated correctly on the washer fluid reservoir (8). | |
6 | Remove screws (9) of washer fluid reservoir (8) | ||
7 | Disconnect electrical connectors | Electrical connectors of: washer fluid pump (M5/1), HCS pump (M5/2), rear-end door washer fluid pump (M5/3), windshield washer system fluid level indicator switch (S42). | |
8 | Remove cable ties from hoses (5) | ||
9 | Lift washer fluid reservoir (8) from wheel well and empty washer fluid | Pour washer fluid into a suitable vessel. | |
Installation: Only pour in the washer fluid after the operations have been completed. | |||
10 | Detach hose (5) from rear-end door washer fluid pump (M5/3) | Mark the hose (5) and the rear-end door washer fluid pump (M5/3). | |
11 | Detach hose (5) from washer fluid pump (M5/1) | Mark the hose (5) and the washer fluid pump (M5/1). | |
12 | Detach hose from fitting (7) of HCS pump (M5/2) | To do so, detach clip (6) and remove hose. | |
13 | Install in the reverse order | ||
14 | Pour in washer fluid | See owner's manual. | |
15 | Perform function test of the windshield washer system |
Referenced documents
- ar2030p4950gr Remove/install expansion reservoir
- ar8310p9998gm Remove and install air plenum chamber and water collector
- ar8310p9998gm
- as2000z000101a Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant.