Model | 461.239/336/338 |
Model | 461.321/322 |
Model | 461.332/333/334 |
except code ZS4 (Special protection version FB4) | |
except code ZS6 (Special protection version FB6) | |
except code ZS7 (Special protection version FB7) | |
Model | 463.221/225/228/231/233/321/325/328/331 |
up to model year 2000 | |
with code 979 (Special protection MB Guard) | |
Model | 463.241 |
up to model year 2000 | |
except code 979 (Special protection MB Guard) |
5 | Bottom hinge screws |
6 | Top hinge screws |
P72.12-0278-01
P72.12-0275-01
P72.12-0268-01
P80.20-2511-01
P72.12-0264-01
2 | Power window motor electric line |
M14/8x1 | Left rear door CL [ZV] motor connector |
M14/9x1 | Right rear door CL [ZV] motor connector |
4 | Passage grommet |
Warning | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
| Remove/install | ||
1 | Disconnect ground line from battery. | Model 461.239/336/338 | |
Model 461.332/333/334 | |||
Model 461.239/336/338 | |||
2 | Remove door lining from the rear door. | Model 461.239/336/338 | |
Model 461.239/336/338 | |||
Model 461.239/336/338 | |||
Model 461.239/336/338 | |||
Model 461.239/336/338 | |||
Model 463.241 | |||
Model 461.332/333/334 | |||
Model 461.239/336/338 | |||
Model 461.239/336/338 | |||
3 | Carefully release door foil. | ||
4 | Check door foil for damage. | If there are problems, | |
| |||
Replace door foil. | |||
5 | Disconnect power window motor electric line (2). | Installation: Ensure that the electric line is routed and mounted correctly. | |
6 | Remove and disconnect left rear door central locking motor connector (M14/8x1) and right rear door central locking motor connector (M14/9x1) from the bracket and release and disconnect. | Installation: Ensure that the electric lines are routed and mounted correctly. | |
7 | Remove electric plug contacts of the feed line on the body-side from the plug housing. | General repair methods for wiring harness | |
Insulate and mark electric plug contacts. | |||
8 | Pull feed-through grommet (4) out of the door pillar and rear door and pull electric lines out of the rear door. | Installation: Check feed-through grommet (4) is correctly seated. | |
9 | Check feed-through grommet (4) for damage. | If there are problems, | |
| |||
replace feed-through grommet (4). | |||
10 | Remove bottom hinge screws (5) and top hinge screws (6). | Helper required. | |
Support rear door. | |||
Bolt, hinge to body | |||
11 | Remove rear door. | Installation: Observe markings on the adjusting sheets. | |
Marking adjusting sheets under the hinges. | |||
12 | Install in the reverse order. | ||
13 | Adjust rear door. |
|
Referenced documents
- ar0019p0100a General repair methods for wiring harness
- ar5410p0003g Disconnect/connect battery ground line
- ar5410p0003gl Disconnect/connect battery ground line
- ar7210p1000gl Remove/install door lining on front door
- ar7210p1000glc Remove/install door lining on front door
- ar7210p1000gls Remove/install front door lining
- ar7210p1000gv Remove/install front door lining
- ar7210p1000h Remove/install front door lining
- ar7210p1000sg Remove/install front door lining
- ar7210p1000si Remove/install front door lining
- ar7212p0650a Adjust rear door
- ar7212p1010gls Remove/install rear door lining
- ar7212p1010gv Remove/install rear door lining
- ar7212p1010sg Remove/install rear door lining
- as0000z001101a Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.