Remove/install trim at C-pillar

AR68.30-S-4490E

Remove/install trim at C-pillar

02.03.2017

Model

447.7, 448.7

with code V23 (Interior panelling higher execution)

Model

447.8, 448.8

Shown on left side of vehicle on model 447.8 except code ZK7 (MARCO POLO equipment) and except code ZH6 (Marco Polo ACTIVITY)

1

Cover

2

Screw

3

Coat hook

4

C-pillar paneling

Model 447.7 with code D57 (Full-width partition wall on C-pillar with window)

4

C-pillar paneling

6

Bolts

 Warning

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

No parts of the body or limbs should be within the operating area when the components are moving.

AS00.00-Z-0011-01A

Topical note

Notes on carrying out repair work in the vehicle interior

AH68.00-N-0001-01S

 

Remove/install

1

Take off cover (1)

If installed.

2

Unscrew bolt (2) and remove coat hook (3)

If installed.

3

Remove rear curtain from C-pillar paneling (4)

Model 447.7
with code T19 (Sliding door left)
with code V23 (Interior panelling higher execution)
with code ZH6 (Marco Polo ACTIVITY)

4

 Remove front and rear curtain from C-pillar paneling (4)

Model 447.7
with code V23 (Interior panelling higher execution)
with code ZH6 (Marco Polo ACTIVITY)
except code T19 (Sliding door left)
When removing left C-pillar panel (4).

5

Remove C-pillar partition wall

Model 447.7
with code D57 (Full-width partition wall on C-pillar with window)
with code V23 (Interior panelling higher execution)

AR68.74-S-0715EE

6.1

Unclip C-pillar paneling (4) in lower area (arrows A) and pull out of guide downward at top and remove

Model 447.7
with code V23 (Interior panelling higher execution)
except code D57 (Full-width partition wall on C-pillar with window)
except code ZH6 (Marco Polo ACTIVITY)
Model 447.8
except code ZK7 (Equipment line MARCO POLO)
Model 448.7
with code V23 (Interior panelling higher execution)
Model 448.8
When removing right C-pillar paneling (4).

 Installation: Ensure that window and door frame seal are seated correctly.

 Long wedge

*115589035900

6.2

Unclip C-pillar paneling (4) in lower area (arrows A) and front (arrows B) and pull out of guide downward at top and remove

Model 447.7
with code V23 (Interior panelling higher execution)
except code D57 (Full-width partition wall on C-pillar with window)
except code ZH6 (Marco Polo ACTIVITY)
Model 447.8
except code ZK7 (Equipment line MARCO POLO)
Model 448.7
with code V23 (Interior panelling higher execution)
Model 448.8
When removing left C-pillar panel (4).

 Installation: Ensure that window and door frame seal are seated correctly.

 Long wedge

*115589035900

6.3

Unclip C-pillar paneling (4) in lower area (arrows A) and pull out of guide downward at top and remove

Model 447.8
with code ZK7 (Equipment line MARCO POLO)
When removing right C-pillar paneling (4).

 Installation: Ensure that window and door frame seal are seated correctly.

 Long wedge

*115589035900

6.4

Detach C-pillar paneling (4) from upper mount and remove

Model 447.8
with code ZK7 (Equipment line MARCO POLO)
When removing left C-pillar panel (4).

 Installation: Position C-pillar paneling  (4) at bottom of C-pillar and press upper shackle into mount.
Ensure that window seal is seated correctly.

 Long wedge

*115589035900

6.5

Unclip C-pillar paneling (4) in lower area (arrows A) and pull out of guide downward at top and extend front and rear curtain rod

Model 447.7
with code V23 (Interior panelling higher execution)
with code ZH6 (Marco Polo ACTIVITY)
except code T19 (Sliding door left)
When removing left C-pillar panel (4).

 Installation: Ensure that window seal is seated correctly.

 Long wedge

*115589035900

6.6

Unclip C-pillar paneling (4) in lower area (arrows A) and pull out of guide downward at top and extend rear curtain rod remove

Model 447.7
with code V23 (Interior panelling higher execution)
with code ZH6 (Marco Polo ACTIVITY)
except code T19 (Sliding door left)
When removing right C-pillar paneling (4).

 Installation: Ensure that window and door frame seal are seated correctly.

 Long wedge

*115589035900

6.7

Unclip C-pillar paneling (4) in lower area (arrows A) and pull out of guide downward at top and extend rear curtain rod remove

Model 447.7
with code T19 (Sliding door left)
with code V23 (Interior panelling higher execution)
with code ZH6 (Marco Polo ACTIVITY)

 Installation: Ensure that window and door frame seal are seated correctly.

 Long wedge

*115589035900

6.8

Unscrew bolts (6) and remove C-pillar paneling (4)

Model 447.7
with code D57 (Full-width partition wall on C-pillar with window)
with code V23 (Interior panelling higher execution)

  Observe assembly position of C-pillar paneling (4).

7

Prepare C-pillar paneling (4) for installation

Model 447.7
with code V23 (Interior panelling higher execution)
with code ZH6 (Marco Polo ACTIVITY)
When replacing C-pillar paneling  (4).

AR68.30-S-0111-01E

8

Install in the reverse order