P68.30-3419-09
Shown with code (540) Electric rear window roller blind |
1 | Rear shelf | 3 | Roller sun blind (with code (540) Electric roller blind for rear window ) | 6 | Screw | ||
1.1 | Rear shelf rear section (with code (540) Electric roller blind for rear window ) | 4 | Clip | 7 | Guide | ||
2 | Center seat belt | 5 | Expansion clip | 8 | Frame |
P68.30-3420-09
With code (540) Electric rear window roller blind |
1.1 | Rear shelf rear section (with code (540) Electric roller blind for rear window ) | 9 | Guide | E21x1 | Center brake lamp electrical connector | ||
3 | Roller sun blind (with code (540) Electric roller blind for rear window ) | 10 | Screw |
P68.30-3421-08
Shown with code (540) Electric rear window roller blind |
1 | Rear shelf | 11 | Center brake lamp cover | 14 | Speaker cover | ||
1.1 | Rear shelf rear section (with code (540) Electric roller blind for rear window ) | 12 | Supports | X19/3 | Rear window roller sun blind motor electrical connector | ||
3 | Roller sun blind (with code (540) Electric roller blind for rear window ) | 13 | Top Tether cover |
Danger ! | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
| Notes on sensor system for trunk lid opening/closing | ||
| Remove/install | ||
1.1 | Remove rear seat backrest | MODEL 212.0/1 | |
1.2 | Remove rear seat backrest | MODEL 212.0/1 | |
1.3 | Remove side upholstery | MODEL 212.0 | |
2 | Unscrew bolt (6) and remove belt end fitting from center seat belt (2) | ||
3 | Loosen paneling on left and right C-pillar and lay down to side with seat belts installed | ||
Do not remove belt end fittings. | |||
4 | Remove rear wall window | MODEL 212.0 | |
5 | Remove rubber from left and right expansion clip (5) and remove expansion clips (5) | ||
6 | Remove clips (4) | MODEL 212.0/1 | |
7.1 | Pull rear shelf (1) toward front out of guides (7) | MODEL 212.0/1 | |
7.2 | Pull rear shelf (1) toward front out of guides (9) and guide (arrow) | MODEL 212.0/1 | |
8 | Lift rear shelf (1) and disconnect electrical connector on center brake lamp (E21x1) | MODEL 212.0/1 | |
9 | Unclip frame (8) from rear shelf (1), guide center seat belt (2) through opening in rear shelf (1) and remove rear shelf (1) | ||
10 | Turn guides (9) 45° counterclockwise and remove | MODEL 212.0/1 | |
11 | Loosen bolts (10) in trunk, push roller sun blind (3) in direction of arrow and guide bolts (10) out of holes | MODEL 212.0/1 | |
12 | Disconnect electrical connector on rear window roller sun blind motor (X193) and remove rear shelf rear section (1.1) with roller sun blind (3) until center brake lamp electrical connector (E21x1) is accessible | MODEL 212.0/1 | |
13 | Disconnect center brake lamp electrical connector (E21x1) and remove rear shelf rear section (1.1) with roller sun blind (3) | MODEL 212.0/1 | |
14 | Install in the reverse order | ||
| Disassemble/assemble | ||
15 | Remove roller sun blind (3) from rear shelf rear section (1.1) | Installation: Ensure that roller sun blind (3) is inserted into mounts (12). | |
16 | Unclip center brake lamp cover (11) from rear shelf rear section (1.1) or rear shelf (1) and remove | Depending on vehicle equipment. | |
17 | Unclip loudspeaker cover (14) and top tether cover (13) from rear shelf (1) and remove | ||
18 | Assemble in the reverse order |
Referenced documents
- ah8061p000101a Notes on HANDS-FREE ACCESS
- ar6720p2000eg Remove/install rear wall window
- ar6830p4490ew Remove/install trim at C-pillar
- ar9112p1620cw Remove/install rear seat backrest
- ar9112p1620ew Remove/install rear seat backrest
- ar9112p1710cw Remove/install rear seat backrest side bolster
- as0000z001101a Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.