Remove/install side load compartment paneling

AR68.30-P-1185MEC

Remove/install side load compartment paneling

07.04.2020

Model

167.3

Modification notes

12.02.2020

Remove load compartment floor, added.

Operation steps 5, 6

Shown on the right side of the vehicle with code 293 (side airbags in the rear) and code 489 (AIRMATIC)

1

Electrical connector

5

Cargo area paneling

2

Side section

6

Electrical connectors

3

Screw

S105

Rear-end lowering switch

4

Cargo retainers

X58/12

Luggage compartment socket

Shown on right side of vehicle

5

Cargo area paneling

 Warning

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

No parts of the body or limbs should be within the operating area when the components are moving.

AS00.00-Z-0011-01A

Topical note

Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

Notes on HANDS-FREE ACCESS

AH80.61-P-0001-01A

 

Remove/install

1

Open liftgate and remove rear shelf.

2

Remove luggage security in the load compartment.

Model 167.3
with code 942 (Load compartment/trunk package)
Model 167.3
with code U40 (Safety net for luggage cover)

3

Switch off ignition and store transmitter key outside of transmitter range (min. 2 m).

4

Disconnect ground line from on-board electrical system battery.

Model 167.3
with code 293 (Sidebag in rear left and right)

AR54.10-P-0009ME

5

Unclip rear load compartment floor, lift, and disconnect electrical connector of KEYLESS-GO antenna in front load compartment.

Model 167.317/354

 The KEYLESS-GO antenna is located at the bottom front of the load compartment floor.

 Long wedge

*115589035900

6

Remove load compartment floor from vehicle.

 Model 167.317/354
The KEYLESS-GO antenna remains on the load compartment floor.

7

Remove edge guard of the liftgate opening in the working area.

8

Remove rear-end center-section trim.

AR68.30-P-4786ME

9

Remove edge guard of the rear door in the working area.

10

Remove rear door sill.

AR68.30-P-4100ME

11

Remove rear seat cushion.

AR91.12-P-1021ME

12

Disconnect electrical connector (1) from the side section (2) of the seat backrest.

Model 167.3
with code 293 (Sidebag in rear left and right)

13

Remove bolt (3) .

 Bolt, side section of rear seat backrest to holder

*BA91.12-P-1012-03M

14

Remove side section (2) of seat backrest.

15

Fold seat backrest in the rear passenger compartment toward the front.

16

Remove cargo retainers (4).

 Bolt, cargo retainers to body

*BA68.50-P-1001-03F

17

Unclip load compartment trim (5) (arrows).

 Long wedge

*115589035900

18

Disconnect electrical connectors (6).

When removing the right load compartment trim (5).


Do not crush or kink or subject electric lines to tension.
This will result in damage to the lines and can impair their function.

 The number of electrical connectors (6) varies depending on the vehicle equipment.

19

Remove load compartment trim (5) from vehicle.

20

Remove rear-end lowering switch (S105) from the right load compartment trim (5).

Model 167.3
with code 489 (AIRMATIC)
When installing a new right load compartment trim (5).

21

Remove trunk socket (X58/12) from the right load compartment trim (5).

When installing a new right load compartment trim (5).

 Pliers

*169589003700

22

Install in the reverse order.

 Cargo retainers

Number

Designation

Model 167

BA68.50-P-1001-03F

Bolt, cargo retainers to body

Nm

24

 Rear seats

Number

Designation

Model 167

BA91.12-P-1012-03M

Bolt, side section of rear seat backrest to holder

M6

Nm

7