AR47.10-P-4100PP | Remove/install fuel tank | 18.1.10 |
MODEL 203.004 /006 /204 /206 /706 with ENGINE 611.962
MODEL 203.016 /216 with ENGINE 612.962
MODEL 209.316 with ENGINE 612.967
P47.10-2066-09
Shown on model 203.006 with engine 611.962
1 Cap
2 Plug connection
4 Hand brake cable
5 Relay lever
6 Outer cable
7 Wheelhousing lining
8 Hose clamps
9 Fuel lines
10 Bolt
11 Filler pipe
12 Floor coverings
B4/1 Left fuel level sensor
P47.10-2078-06
13 Fuel pipe
14 Fuel feed pipe
15 Hose clamp
16 Shield
17 Fuel tank
18 Retaining straps
19 Propeller shaft
Modification notes
| Remove/install | ||
| Notes on self-locking nuts and bolts | All models | |
Danger! | Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel and risk of injury to eyes and skin caused by contact with fuel. | No fire, sparks, open flames or smoking. Wear protective clothing when handling fuel. | |
1 | Empty fuel tank (17) | ||
Pay attention to fuel quantity. | |||
2 | Remove rear axle. | ||
3 | Remove end cover (1) of body | ||
4 | Disconnect connector (2) of fuel level sensor, left half of tank (B4/1) | ||
5 | Detach hand brake cable (4) at relay lever (5) | ||
6 | Pull outer cable (6) out of fixture | Press together two retaining tabs (arrows) for this step. | |
7 | Remove right rear wheelhousing liner (7) | ||
8 | Take off hose clamps (8) | Check hose clamps (8) for damage, replace if necessary. | |
9 | Detach fuel lines (9) | If fuel hoses are firmly attached, these must be cut in with a knife and then detached. Otherwise there is danger, that on firmly attached fuel hoses the fittings can tear off at the fuel tank. | |
10 | Undo bolt (10) of filler pipe (11) | ||
11 | Remove floor coverings (12) | ||
12 | Detach fuel line (13) to fuel pipe (14) | Installation: Check hose clamp (15) and fuel line (13) for damage, replace if necessary. | |
| |||
13 | Remove shield (16) | ||
14 | Support fuel tank (17) | ||
15 | Unscrew retaining straps (18) at body | | |
16 | Remove fuel tank (17) | After removing the fuel tank, tie up propeller shaft (19) with a cable tie. | |
17 | Dispose of fuel tank | Only if required. | |
| Disposing of fuel tanks | ||
18 | Install in the reverse order |
Fuel tank
Number | Designation | Model | Model | ||
BA47.10-P-1004-01E | Fuel tank retaining straps to underbody | M 8 | Nm | 20 | 20 |
M 18 | Nm | 60 | 60 | ||
Fuel tank
Number | Designation | Model 203 | Model 209 | ||
BF47.10-P-1001-01A | Fuel tank capacity | Total filling capacity | Liters | 62 | 62 |
Reserve capacity | Liters | 8 | 8 | ||
Clamping device
000 589 40 37 00
Referenced documents
- ah0000n000101a Notes on self-locking nuts and bolts
- ar3510p0010p
- ar3510p0010p Remove/install complete rear axle
- ar4710p4001pp Emptying/filling fuel tank.
- ar8810p1400p Remove/install fender liner in rear fender
- as4700z000101a Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel as well as risk of injury to eyes and skin caused by contactwith fuel.
- os4710p000101a Disposing of fuel tanks