P47.10-2066-09
1 Cap
2 Electrical connector
4 Hand brake cable
5 Relay lever
10 Bolt
11 Filler pipe
12 Floor coverings
B4/1 Left fuel level sensor
6 Outer cable
7 Wheelhousing lining
8 Hose clamps
9 Fuel lines
P47.10-2078-06
13 Fuel pipe
14 Fuel feed pipe
15 Hose clamp
16 Shield
17 Fuel tank
18 Tank retaining strap
19 Propeller shaft
Modification notes
| Remove/install | ||
Danger! | Risk of death caused by vehicle slipping or toppling off the lifting platform. | Align vehicle between columns of lifting platform and position four support plates at lifting platform support points specified by vehicle manufacturer. | |
Danger! | Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel and risk of injury to eyes and skin caused by contact with fuel. | No fire, sparks, open flames or smoking. Wear protective clothing when handling fuel. | |
| Notes on self-locking nuts and bolts | ||
1 | Empty fuel tank (17) | Pay attention to fuel quantity. | |
Fuel tank capacity | |||
2 | Remove rear axle. | ||
3 | Remove cap (1) on body | ||
4 | Disconnect plug in electrical plug connection (2) on fuel level sensor, left half of tank (B4/1) | ||
5 | Detach hand brake cable (4) at relay lever (5) | ||
6 | Pull outer cable (6) out of fixture | Press together the two retaining tabs (arrows) for this step. | |
7 | Remove right rear wheelhousing liner (7) | ||
8 | Take off hose clamps (8) | Installation: Check hose clamps (8) for damage and replace if necessary. | |
9 | Detach fuel lines (9) | In the event of fixed fuel lines (9) cut these with a knife and then detach. There is otherwise risk of fixed fuel lines (9) shearing off the connections at the fuel tank (17). | |
10 | Undo bolt (10) of filler pipe (11) | ||
11 | Remove floor coverings (12) | ||
12 | Detach fuel line (13) to fuel pipe (14) | Installation: Check hose clamp (15) and fuel line (13) for damage, replace if necessary. | |
Clamp | |||
13 | Remove shield (16) | ||
14 | Support fuel tank (17) | ||
15 | Unscrew tank retaining straps (18) at body | Fuel tank retaining straps to underbody | |
16 | Remove fuel tank (17) | After removing fuel tank (17), tie up propeller shaft (19) with a cable tie. | |
17 | Dispose of fuel tank (17) | Only when replacing fuel tank (17) | |
| Disposing of fuel tanks | ||
18 | Install in the reverse order |
Fuel tank
Number | Designation | Model | Model | ||
BA47.10-P-1004-01E | Fuel tank retaining straps to underbody | M 8 | Nm | 20 | 20 |
M 18 | Nm | 60 | 60 | ||
Fuel tank
Number | Designation | Model | Model | ||
BF47.10-P-1001-01A | Fuel tank capacity | Total filling capacity | Liters | 62 | 62 |
Reserve capacity | Liters | 8 | 8 | ||
Clamping device
000 589 40 37 00
Referenced documents
- ah0000n000101a Notes on self-locking nuts and bolts
- ar3510p0010p
- ar3510p0010p Remove/install complete rear axle
- ar4710p4001pm Empty / fill fuel tank
- ar8810p1400p Remove/install fender liner in rear fender
- as0000z001001a Risk of death caused by vehicle slipping or toppling off of the lifting platform.
- as4700z000101a Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel as well as risk of injury to eyes and skin caused by contactwith fuel.
- os4710p000101a Disposing of fuel tanks