Remove/install threaded ring on through-drive input shaft

AR35.30-W-0476A

Remove/install threaded ring on through-drive input shaft

26.10.10

10.10.10

Clean thread on threaded ring (2) and through-drive cover (1) and make sure they are free of grease, added.

Operation step 4

Apply light coating of sealant to complete thread surface of threaded ring (2), added.

Step 5

*BR00.45-Z-1009-01A

Apply light coating of sealant to first third of thread surface on through-drive cover (1), added.

Operation step 6

*BR00.45-Z-1009-01A



Removing

1

Remove drive flange

AR35.30-W-0473MA

2

Remove locking plate (4) on threaded ring (2)

3

Remove threaded ring (2)

 Claw wrench

*748589010700



Install

4

Clean thread on threaded ring (2) and through-drive cover (1) and make sure they are free of grease.

5

Apply light coating of sealant to complete thread surface of threaded ring (2).

*BR00.45-Z-1009-01A

6

Apply light coating of sealant to first third of thread surface on through-drive cover (1).

*BR00.45-Z-1009-01A

7

Screw threaded ring (2) all the way into the through-drive cover (1)

 Claw wrench

*748589010700

8

Adjust axial play of through-drive

 The installation depth of the threaded ring determines the axial play of the through-drive shaft. It therefore has to be ensured that the threaded ring is tightened to the corresponding tightening torque depending on the special tool used.

AR35.30-W-0476-01A

 The higher tightening torque must be used when tightening with a puller directly at the threaded ring.

If the claw wrench is used the ring must be tightened with the lower tightening torque. The higher tightening torque is achieved at the threaded ring due to the lever effect of the claw wrench.

 Rear axle 748.261/271

*BA35.30-N-1012-04A

 Rear axle 748.703

*BA35.30-N-1012-04B

 Claw wrench

*748589010700

9

Secure threaded ring (2)

 When installing the locking plate (4) if possible do not change the position of the threaded ring.

If the locking plate (4) cannot be installed, the threaded ring must be tightened by a maximum of 5°.

 Claw wrench

*748589010700

 Rear axle 748.261/271

*BA35.30-N-1005-04A

 Rear axle 748.703

*BA35.30-N-1005-04B

10

Mount drive flange

AR35.30-W-0473MA

Number

Designation

Rear axle 748.26/27 with through-drive, ring gear 233 mm dia.

BA35.30-N-1005-04A

Bolt, locking plate to through-drive cover

Nm

35

BA35.30-N-1012-04A

Threaded ring to through-drive cover

With claw-type wrench

Stage 1

Nm

215

On threaded ring itself

Nm

250

Release distance

Stage 2

°

-45...-50

Number

Designation

Rear axle 748.703 with through-drive, 233 mm dia. ring gear

BA35.30-N-1005-04B

Bolt, locking plate to through-drive cover

Nm

35

BA35.30-N-1012-04B

Threaded ring to through-drive cover

Stage 1

With claw-type wrench

Nm

215

On threaded ring itself

Nm

250

Stage 2

Release distance

°

-45...-50

Number

Designation

Order number

BR00.45-Z-1009-01A

Sealing compound Loctite 574, 50 ml

A 001 989 89 20 10