Remove/install engine mount

AR22.10-P-1100RT

Remove/install engine mount

15.2.12

28.3.07

Screw/bolt, engine support to cylinder crankcase, 1st stage

*BA22.10-P-1003-01S

 

Remove/install

Danger!

Risk of death caused by vehicle slipping or tilting off of the vehicle lift.

Align vehicle between vehicle lift columns and position four support plates at vehicle lift support points specified by vehicle manufacturer.

AS00.00-Z-0010-01A

 Danger!

Risk of injury caused by fingers being pinched or crushed when removing, installing or aligning hoods, doors, trunk lids, liftgates or sliding roof

Keep body parts and limbs well clear of moving parts.

AS00.00-Z-0011-01A

 Danger!

Risk of explosion caused by escaping oxyhydrogen gas. Risk of injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte (contains diluted sulfuric acid) or metal spatter due to short circuit. Risk of burn injuries caused by short circuit. Risk of poisoning caused by swallowing battery electrolyte (contains diluted sulfuric acid) or absorption of lead over the skin or orifices

No fire, sparks, open flames or smoking.

Wear acid-resistant gloves and clothing and safety glasses with side guards.

Do not place any conductive objects on the battery and avoid any short circuit from battery positive to ground.

Only fill liquid battery electrolyte (diluted sulfuric acid) into suitable and appropriately marked containers.

AS54.10-Z-0001-01A



Notes on battery

All models

AH54.10-P-0001-01A



Notes on self-locking nuts and bolts

All models

AH00.00-N-0001-01A

1

Open engine hood and raise to vertical position

AR88.40-P-1000RT

2.1

Disconnect ground line from battery

 Only when removing engine mount on the right side.

AR54.10-P-0003RT

3

Raise vehicle with vehicle lift

AR00.60-P-1000RT

4

Remove left and right suction fan duct

5

Remove air filter housing

AR09.10-P-1150RT

6

Put on engine carrier arm

Engine support device, engine hoist
gotis://A_01_09.0

Engine lifting device side adapter for model 251

7

Detach lower engine compartment paneling

AR61.20-P-1105RT

8

Remove screw/bolts (5) from the right and left engine mounts (1, 3)



*BA22.10-P-1001-03F

Right hand engine mount

9

Remove exhaust system partially

 Only remove exhaust system up to the flange connection from front muffler.

AR49.10-P-7000RT

10

Remove starter

AR15.30-P-7100RT

11

Remove the bolt (9) of the ground line

 Hang ground line to the side so that these are not damaged when lifting the engine using the engine support frame.



*BA22.10-P-1003-01S

12

Remove screw/bolt (6) from engine mount (1)



*BA22.10-P-1002-03F

 Tool kit

*000589109900

 Connection piece

*210589001600

 Four-point drive

*210589011600

13

Remove shield (2) and right engine mount (1) towards the front

 Installation: Observe anti-twist lock for the engine mount (7) and anti-twist lock for the shield (8).

 Observe environmental protection regulations for disposal of engine mounts,

Dispose engine mounts into mixed scrap.

14

Perform basic programming

AR00.19-P-0200RT

Left engine mount

15

Remove left catalytic converter

AR49.10-P-5500RTN

16

Remove screw/bolt (6) from engine mount (3)



*BA22.10-P-1002-03F

 Tool kit

*000589109900

 Connection piece

*210589001600

 Four-point drive

*210589011600

17

Remove shield (4) and left engine mount (3) downwards below

 Installation: Observe anti-twist lock for the engine mount (7) and anti-twist lock for the shield (8).

 Observe environmental protection regulations for disposal of engine mounts. Give engine mount to mixed scrap metal.

18

Install in the reverse order

Number

Designation

Engine
113.971
in model 251

BA22.10-P-1003-01S

Screw/bolt, engine support to cylinder crankcase

Stage 1

Nm

20

Stage 2

°

90

Number

Designation

Model 251

BA22.10-P-1001-03F

Screw/bolt, front engine mount to front axle carrier

Nm

53

BA22.10-P-1002-03F

Bolt connecting front engine mount to engine support

Nm

53